Pioneer SC-LX501 Basic Manual English/French - Page 10

in case of, s 5 to 7

Get Pioneer SC-LX501 PDF manuals and user guides View all Pioneer SC-LX501 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

> Before start > Hookup > Setup > Playback > Part Names 3/8˝ (10 mm) 1 in case of: 2 Pages 5 to 7 Connect 1234569:. Up to two powered subwoofers can be connected. The same signal is output from each of the SUBWOOFER jacks. 0 Apart from these connections, you can also connect surround back speakers 7 and 8. However, you can only output audio from one set of 78 or 9: at a time. When you have connected both, you can select which speakers to prioritize with "Speakers" (P26) in the AV Adjust. Setup 0 Settings for the speaker configuration you have connected need to be made in "1. Full Auto MCACC" (P20) in Initial Setup. Note that if you are using height speakers, set "Speaker Channels" to "5.1.2 ch" in the setting screen. Select "7.1.2 ch" if you have connected both surround back speakers and height speakers. 1 Speaker cable, 2 Subwoofer cable 10 Make sure the exposed wires of the speakers do not stick out of the speaker terminals when connecting. If the exposed wires of the speakers touch the rear panel or the + and - wires touch each other, the protection circuit will be activated.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
10
> Before start
> Hookup
> Setup
> Playback
> Part Names
2
1
3/8˝
(10 mm)
1
Speaker cable,
2
Subwoofer cable
in case of:
Pages 5 to 7
Connect
123456
9:
. Up to two powered
subwoofers can be connected. The same signal is output
from each of the SUBWOOFER jacks.
0
Apart from these connections, you can also connect
surround back speakers
7
and
8
. However, you can
only output audio from one set of
78
or
9:
at a time.
When you have connected both, you can select which
speakers to prioritize with "Speakers" (
P26) in the AV
Adjust.
Make sure the exposed wires of the speakers do not stick out of
the speaker terminals when connecting. If the exposed wires of
the speakers touch the rear panel or the + and – wires touch each
other, the protection circuit will be activated.
Setup
0
Settings for the speaker configuration you have
connected need to be made in "1. Full Auto
MCACC" (
P20) in Initial Setup. Note that if you
are using height speakers, set "Speaker Channels"
to "5.1.2 ch" in the setting screen. Select "7.1.2 ch"
if you have connected both surround back
speakers and height speakers.