Ricoh Aficio GX e3300N User Guide - Page 705

1. Remove the cover from the rear side of the carriage unit. D3 Remove carriage Ჿ Attach new carriage 1. Attach the 2 FFCs. Fit the carriage unit into the Styrofoam holders as shown in the photo. 3. Remove the humidity retention cap. Humidity retention cap Cover 2. Remove the 2 FFCs. 3. Secure the FFC to the jigs. CAUTION: 䊶Be careful not to fold them. 䊶One FFC is longer than the other. Make sure to attach the longer FFC in the right position shown in the photo in Step D-2 (and shorter FFC in the left position). 4. Re-insert the guide rod into the carriage. (See Step C-4) 5. Remove the jigs. (See Step C-2) 6. Attach the belt. Upper belt Do not fold the FFCs Carriage Lower Left belt Appendix: Accessories 1. Carriage unit Removal of the carriage unit 2. Attach the carriage's rear cover. completed. Slide the belt into the gap 7. Pass the bundled encoder strip (not the original encoder strip) through the opening between the carriage sensors. 5 2. Procedure 3. Waste ink tank 4. Ink cartridges Left Hole Marking Right CAUTION: If you wipe the surface from the left side, this may damage the plate spring. Left side 22. Reset the envelope lever to standard position.See Step B-2. Carriage attachment completed. F Adjustment after replacement 1. Open the ink cartridge cover before you turn on the machine main power. Otherwise the machine will perform auto maintenance and consume a large amount of ink. Left Through this opening Right 8. Hook the right end of the encoder sheet first, then hook the left end. Right side 9. Clean the strip with alcohol by wiping the surface from right to left. Clean from right side Plate spring 2. Enter SP mode. 3. Execute SP5101. (Some values related to print head will be reset) 10. Attach the cam (screw x1). See Step C-3-5. 11. Attach the spring. See Step C-3-4. 12. Attach the linkage. See Step C-3-2. 13. Attach the stay plate. ĭ Į Ĭ 4. Install the starter ink cartridges. 5. Install the ink collector unit. 6. Close the ink cartridge cover. IMPORTANT: Ink initialization will start. During the initialization, do not open any covers, or turn off the power. The entire process will take about seven minutes. 7. Print out the nozzle check pattern. [Menu]ą[Maintenance]ą[Nozzle check] IMPORTANT: Check to see if the nozzle is clogged, and If it is, perform print head cleaning. 8. Adjust the print head position. [Menu]ą[Maintenance]ą[Head Position]*1 Order to fasten screws 14. Attach the guide lock. See Step C-3-3. 9. Adjust the registration. [Menu]ą[Maintenance]ą[Registration]*2 15. Attach the ink supply unit See Step B-1. 10. Adjust the paper feed. [Menu]ą[Maintenance]ą[Adj. Paper Feed] 16. Attach the front cover. See Step A-7. 17. Attach the operation panel. See Step A-6. 11. Print out the color demo page. [Menu]ą[List/Test Print]ą[Color Demo Page] 18. Attach the right cover.See Step A-4. 12. Print out the engine summary (SP 5200). 19. Attach the upper/inner cover. See Step A-3. 13. Replace the ink collector unit and ink cartridges with the ones 20. Attach the ink cartridge cover. See Step A-5. the customer was originally using. 21. Attach the output tray and paper tray. See Step A-1 and 2. 6 *1: 䇸Standard䇹-䇸High Speed䇹-䇸High Quality 2: Only "Tray 1-Plain Paper" 5. Guide rod fastening tool (x2; right side of photo), guide rod removal tool (x1; left side of photo) 6. Main scan encoder sheet Notice: Please be informed of the following as this kit is commonly used with Japanese models. • Both English and Japanese procedure are bundled. • Ink cartridges are are labeled in Japanese but can be used in all models. Copyright © 2009 Printed in China EN GB EN US J017-6701A