Samsung ML 3051ND User Manual (ENGLISH) - Page 20

Network menu, Printing a demo Changing the display language (ML-3051N, ML- 3051ND only) - manual

Get Samsung ML 3051ND - B/W Laser Printer PDF manuals and user guides
UPC - 635753625257
View all Samsung ML 3051ND manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Network menu This menu lets you configure the network interface installed in your printer. You can reset the network interface and print a configuration page. Item TCP/IP EtherTalk NetWare Ethernet Speed Wireless Explanation Values: DHCP, BOOTP, Static This item allows you to manually set the TCP/IP addresses or receive the addresses from the network. • DHCP: The DHCP server allots the IP address to you automatically. • BOOTP: The BOOTP server allots the IP address to you automatically. • Static: You can enter IP address, subnet mask, and gateway manually. Values: Off, On This item lets you select whether or not you use the EtherTalk protocol. Select On to use the protocol. Values: Auto, 802.2, 802.3, Ethernet II, SNAP, Off This item lets you select the IPX frame type. • Auto: You can set the frame type automatically. • 802.2: Select this value to use the IEEE 802.2 frame type. • 802.3: Select this value to use the IEEE 802.3 frame type. • Ethernet II: Select this value to use the Ethernet 2 frame type. • SNAP: Select this value to use the SNAP frame type. • Off: You can disable the NetWare protocol. Values: Auto, 10M Half, 10M Full, 100M Half, 100M Full This item allows you to select the ethernet speed. Values: WLAN Basic, WLAN Security, WLAN Default Configure the wireless network environments. See page 10.3. Note This menu only appears when an optional wireless network interface card has been installed. Item Clear Setting Network Info Explanation This item performs a simple reset and restores the factory default settings for the network configuration. This setting will only take effect after you have reset the printer. This item print a page showing the network parameters you set. Printing a demo page Print a demo page to make sure that the printer is operating correctly. ML-3050, ML-3051N Press and hold Demo for about 2 seconds. ML-3051N, ML-3051ND 1 Press Menu and then OK when Information appears. 2 Press the Scroll buttons until Demo Page appears and press OK. A demo page prints out. Changing the display language (ML-3051N, ML- 3051ND only) To change the language that is displayed on the control panel, follow these steps: 1 Press Menu until System Setup appears on the bottom line of the display and press OK. 2 Press OK when Language appears. 3 Press the Scroll buttons to select the language you want and press OK. 4 Press Stop to return to Standby mode. 2.6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
2
.6
<
System setup>
Network menu
This menu lets you configure the network interface installed in your
printer. You can reset the network interface and print a configuration
page.
Item
Explanation
TCP/IP
This item allows you to manually set the TCP/IP
addresses or receive the addresses from the
network.
•
DHCP
: The DHCP server allots the IP address to
you automatically.
•
BOOTP
: The BOOTP server allots the IP address
to you automatically.
•
Static
: You can enter IP address, subnet mask,
and gateway manually.
EtherTalk
This item lets you select whether or not you use the
EtherTalk protocol. Select
On
to use the protocol.
NetWare
This item lets you select the IPX frame type.
•
Auto
: You can set the frame type automatically.
•
802.2
: Select this value to use the IEEE 802.2
frame type.
•
802.3
: Select this value to use the IEEE 802.3
frame type.
•
Ethernet II
: Select this value to use the Ethernet 2
frame type.
•
SNAP
: Select this value to use the SNAP frame
type.
•
Off
: You can disable the NetWare protocol.
Ethernet
Speed
This item allows you to select the ethernet speed.
Wireless
Configure the wireless network environments.
See page 10.3.
Note
This menu only appears when an optional
wireless network interface card has been
installed.
Values: DHCP, BOOTP, Static
Values:
Off
,
On
Values: Auto, 802.2, 802.3, Ethernet II, SNAP, Off
Values: Auto, 10M Half, 10M Full,
100M Half, 100M Full
Values: WLAN Basic, WLAN Security, WLAN Default
Printing a demo page
Print a demo page to make sure that the printer is operating correctly.
ML-3050, ML-3051N
Press and hold
Demo
for about 2 seconds.
ML-3051N, ML-3051ND
1
Press
Menu
and then
OK
when
Information
appears.
2
Press the
Scroll
buttons until
Demo Page
appears and press
OK
.
A demo page prints out.
Changing the display language
(
ML-3051N
,
ML-
3051ND
only)
To change the language that is displayed on the control panel, follow
these steps:
1
Press
Menu
until
System Setup
appears on the bottom line of the
display and press
OK
.
2
Press
OK
when
Language
appears.
3
Press the
Scroll
buttons to select the language you want and press
OK
.
4
Press
Stop
to return to Standby mode.
Clear
Setting
This item performs a simple reset and restores the
factory default settings for the network
configuration. This setting will only take effect after
you have reset the printer.
Network
Info
This item print a page showing the network
parameters you set.
Item
Explanation