Sanyo EF60 Instruction Manual, PLC-EF60A - Page 69

WARNING, High voltages are used to operate this projector., Do not attempt to open the cabinet.

Get Sanyo EF60 - PLC SXGA+ LCD Projector PDF manuals and user guides View all Sanyo EF60 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Appendix Some displays are not seen during the Operation. - Check the Display item. (☞ "Setting" on page 52) Only part of image is displayed. (Large/Small) - Check if you are in D. Zoom+/- mode. (☞ p.32, 48) - Change Aspect setting in the Screen setting menu. (☞ p.47) - Adjust Display area and Position in the PC adjust menu. (☞ p.41~42) PIN code dialog box appears at start-up. - PJ PIN code lock is being set. Input a PIN code (1234 or numbers you have set). (☞ "Enter a PJ PIN Code" on pages 27 and 55) Image is not displayed on the monitor connected to the ANALOG OUT terminal. - Select Input 1 with the Input button on the top control or the INPUT 1 button on the remote control, or through the Input Menu. (☞ p.30, 36) - Make sure Analog out is "On." (☞ "Setting" on page 53) The Top Control does not work. - Check if the Keylock function is set. (☞ "Setting" on page 54) The Wireless Remote Control does not work. - Check the batteries. When replacing, the two batteries should be replaced at the same time. (☞ p.17) - Make sure no obstruction is between the projector and remote control. - Make sure you are not too far from the projector when using the remote control. Maximum operating range is 32.8' (10m). - Make sure the ID and CH of the remote control is conformed to the projector. (☞ p.16, 51) - Initialize the remote control ID and CH, and then initialize the remote control ID and CH of the projector as well. (☞ p.16, 51) - Unlock Key lock for the remote control in the Setting Menu. (☞ p.54) - Make sure the wired remote cable is not connected to the projector. (☞ p.25) When all the solutions above fail, try Factory default in the Setting menu. (☞ p.56) USB mouse does not operate properly. - Check cable connection of the USB mouse and the projector. (☞ p.25) SHUTTER button does not operate. - Make sure Shutter protection is "Off." (☞ "Setting" on page 53) Lens position moves when Input is switched. - Check Lens memory for each input. (☞ "Setting" on page 53) Some operating menu items do not appear. - Check the My menu setting. (☞ "Setting" on page 49) Appendix WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Give the model number and explain about the problem. We will advise you how to obtain service. 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
69
Appendix
Some displays are not seen
–
Check the Display item. (
☞
“Setting” on page 52)
during
the Operation.
Only part of image is displayed.
–
Check if you are in D. Zoom+/–
mode. (
☞
p.32, 48)
(Large/Small)
–
Change Aspect setting in the Screen setting menu. (
☞
p.47)
–
Adjust Display area and Position in the PC adjust menu. (
☞
p.41~42)
PIN code dialog box appears at start-up.
–
PJ PIN code lock is being set. Input a PIN code (1234 or numbers you have
set). (
☞
“Enter a PJ PIN Code” on pages 27 and 55)
Image is not displayed on the
–
Select Input 1 with the Input button on the top control or the INPUT 1 button
monitor connected to the ANALOG
on the remote control, or through the Input Menu. (
☞
p.30, 36)
OUT terminal.
–
Make sure Analog out is “On.”
(
☞
“Setting” on page 53)
The Top Control does not work.
–
Check if the Keylock function is set. (
☞
“Setting” on page 54)
The Wireless Remote Control
–
Check the batteries.
When replacing, the two batteries should be replaced
does not work.
at the same time. (
☞
p.17)
–
Make sure no obstruction is between the projector and remote control.
–
Make sure you are not too far from the projector when using the remote
control. Maximum operating range is 32.8’ (10m).
–
Make sure the ID and CH of the remote control is conformed to the
projector. (
☞
p.16, 51)
–
Initialize the remote control ID and CH, and then initialize the remote control
ID and CH of the projector as well. (
☞
p.16, 51)
–
Unlock Key lock for the remote control in the Setting Menu.
(
☞
p.54)
–
Make sure the wired remote cable is not connected to the projector.
(
☞
p.25)
When all the solutions above fail, try Factory default in the Setting menu.
(
☞
p.56)
USB mouse does not operate properly.
–
Check cable connection of the USB mouse and the projector.
(
☞
p.25)
SHUTTER button does not operate.
–
Make sure Shutter protection is “Off.”
(
☞
“Setting” on page 53)
Lens position moves when Input
–
Check Lens memory for each input. (
☞
“Setting” on page 53)
is switched.
Some operating menu items do not appear.
–
Check the My menu setting. (
☞
“Setting” on page 49)
WARNING :
High voltages are used to operate this projector.
Do not attempt to open the cabinet.
If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the
service center. Give the model number and explain about the problem.
We will advise you how to obtain service.
Appendix