Sanyo PDG-DWT50L Owners Manual - Page 114

(2) Image Problems, Lamp Problems

Get Sanyo PDG-DWT50L - WXGA DLP Projector PDF manuals and user guides
UPC - 086483067563
View all Sanyo PDG-DWT50L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 114 highlights

7. Appendix Image Problems Problem: No image appears on the screen 1. Verify the settings on your notebook or desktop PC. 2. Turn off all equipment and power up again in the correct order. Problem: The image is blurred 1. Adjust the Focus on the projector. 2. Press the AUTO PC ADJ. button on the remote control or projector. 3. Ensure the projector-to-screen distance is within the specified range. 4. Check that the projector lens is clean. 5. Remove the lens cover. Problem: The image is blurred and distorted 1. Check the WXGA Mode is set to Off (see page 63). 2. When WXGA Mode is set to On, an XGA (1024 x 768) signal may not be recognized. Set WXGA Mode to Off if this occurs. To check if the signal is recognized, go to "Input" under "Information" menu (see page 90). Problem: The image is wider at the top or bottom (trapezoid effect) 1. Position the projector so it is as perpendicular to the screen as possible. 2. Use the Keystone button on the remote control to correct the problem. Problem: The image is reversed or upside down Check the Ceiling & Rear setting on the Setting menu of the OSD. Problem: The image is streaked 1. Set the Total dots and Fine sync. settings on the Adjust menu of the OSD to the default settings. 2. To ensure the problem is not caused by a connected PC's video card, connect to another computer. Problem: The image is flat with no contrast 1. Adjust the Contrast setting on the Adjust menu of the OSD. 2. Adjust the Brightness setting on the Adjust menu of the OSD. Problem: The color of the projected image does not match the source image. Adjust the Color temp. and Gamma settings on the Detail setting menu of the OSD. Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is securely connected. 2. Ensure the power source is good by testing with another electrical device. 3. Restart the projector in the correct order and check that the Power LED is green. 4. If you have replaced the lamp recently, try resetting the lamp connections. 5. Replace the lamp module. 6. Remove the lens cap. 7. Put the old lamp back in the projector and have the projector serviced. 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
7. Appendix
105
o
Image Problems
Problem: No image appears on the screen
1.
Verify the settings on your notebook or desktop PC.
2.
Turn off all equipment and power up again in the correct order.
Problem: The image is blurred
1.
Adjust the
Focus
on the projector.
2.
Press the
AUTO PC ADJ.
button on the remote control or projector.
3.
Ensure the projector-to-screen distance is within the specified range.
4.
Check that the projector lens is clean.
5.
Remove the lens cover.
Problem: The image is blurred and distorted
1.
Check the WXGA Mode is set to Off (see page
63
).
2.
When WXGA Mode is set to On, an XGA (1024 x 768) signal may not be recognized. Set WXGA
Mode to Off if this occurs. To check if the signal is recognized, go to “Input” under “Information”
menu (see page
90
).
Problem: The image is wider at the top or bottom (trapezoid effect)
1.
Position the projector so it is as perpendicular to the screen as possible.
2.
Use the Keystone button on the remote control to correct the problem.
Problem: The image is reversed or upside down
z
Check the
Ceiling & Rear
setting on the
Setting
menu of the OSD.
Problem: The image is streaked
1.
Set the
Total dots
and
Fine sync.
settings on the
Adjust
menu of the OSD to the default settings.
2.
To ensure the problem is not caused by a connected PC’s video card, connect to another computer.
Problem: The image is flat with no contrast
1.
Adjust the
Contrast
setting on the
Adjust
menu of the OSD.
2.
Adjust the
Brightness
setting on the
Adjust
menu of the OSD.
Problem: The color of the projected image does not match the source image.
z
Adjust the
Color temp.
and
Gamma
settings on the
Detail setting
menu of the OSD.
Lamp Problems
Problem: There is no light from the projector
1.
Check that the power cable is securely connected.
2.
Ensure the power source is good by testing with another electrical device.
3.
Restart the projector in the correct order and check that the Power LED is green.
4.
If you have replaced the lamp recently, try resetting the lamp connections.
5.
Replace the lamp module.
6.
Remove the lens cap.
7.
Put the old lamp back in the projector and have the projector serviced.