Sennheiser ew 300 G2 Instructions for Use - Page 76

Adjusting the audio output level EM 300 G2 only, Adjusting the squelch threshold EM 300 G2 only - microphone

Get Sennheiser ew 300 G2 PDF manuals and user guides View all Sennheiser ew 300 G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

AF Out Adjusting the audio output level (EM 300 G2 only) Via the "AF Out" menu, you can adjust the audio output level of the receivers. The level can be adjusted in eight steps. Adapt the level of the audio output (AF OUT) to the input of the connected unit. The following figures are a guide to the best settings: Line level input: 0 to +18 dB Microphone level input: -24 to -6 dB Squelch Adjusting the squelch threshold (EM 300 G2 only) The receiver is equipped with a squelch that can be adjusted via the "Squelch" menu. The squelch eliminates annoying noise when the transmitter is switched off. It also suppresses sudden noise when there is no longer sufficient transmitter power received by the receiver. Note: Before adjusting the squelch threshold to a different setting, set the volume on a connected amplifier to the minimum. There are three possible squelch settings: y Low = low y Mid = middle y High = high Selecting the setting (Low) reduces the squelch threshold, selecting the setting (High) increases the squelch threshold. Adjust the squelch threshold - with the transmitter switched off - to the lowest possible setting that suppresses hissing noise. IMPORTANT! Notes: If the squelch threshold is adjusted too high, the transmission range will be reduced. Therefore, always adjust the squelch threshold to the lowest possible setting. When in the setting mode of the "Squelch" menu, pressing the ̄ button (DOWN) for more than three seconds will switch the squelch off. "Off" appears on the display. If no RF signal is being received, hissing noise will occur. This setting is for test purposes only. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
31
Adjusting the audio output level (EM 300 G2 only)
AF Out
Via the “
AF Out
” menu, you can adjust the audio output level of the receivers.
The level can be adjusted in eight steps. Adapt the level of the audio output
(AF OUT) to the input of the connected unit. The following figures are a guide
to the best settings:
Line level input:
0 to +18 dB
Microphone level input:
–24 to –6 dB
Adjusting the squelch threshold (EM 300 G2 only)
Squelch
The receiver is equipped with a squelch that can be adjusted via the
“
Squelch
” menu. The squelch eliminates annoying noise when the
transmitter is switched off. It also suppresses sudden noise when there is no
longer sufficient transmitter power received by the receiver.
Note:
Before adjusting the squelch threshold to a different setting, set the
volume on a connected amplifier to the minimum.
There are three possible squelch settings:
Low
=
low
Mid
=
middle
High =
high
Selecting the setting (Low) reduces the squelch threshold, selecting the
setting (High) increases the squelch threshold. Adjust the squelch threshold
– with the transmitter switched off – to the lowest possible setting that
suppresses hissing noise.
IMPORTANT!
Notes:
If the squelch threshold is adjusted too high, the transmission range will
be reduced. Therefore, always adjust the squelch threshold to the lowest
possible setting.
When in the setting mode of the “
Squelch
” menu, pressing the
±
button
(DOWN) for more than three seconds will switch the squelch off. “Off”
appears on the display. If no RF signal is being received, hissing noise will
occur. This setting is for test purposes only.