Sharp A260 Service Manual - Page 22
SW-D2 No. 1 ~ No. 3 Distinctive ringing setting PATTERN 4 and 5 - ux fax machine manual
UPC - 074000033733
View all Sharp A260 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 22 highlights
UX-A260U SW-B6 No. 6 ~ No. 8 Reserved Set to "0". SW-C1 No. 1, No. 2 Reading slice (Binary) Used to determine the set value of reading density in standard/fine mode. The standard setting is "00" (Factory setting is "00") SW-C1 No. 3, No. 4 Reading slice (Half tone) Used to determine the set value of reading density in half tone mode. The standard setting is "00" (Factory setting is "00") SW-C1 No. 5 Line density selection Used to set the transmission mode which is automatically selected when the Resolution key is not pressed. In the copy mode, however, the fine mode is automatically selected unless the Resolution key is manually set to another mode. SW-C1 No. 6 Reserved Set to "0". SW-C1 No. 7 MTF correction in half tone mode This allows selection of MTF correction (dimness correction) in the half tone mode. When "NO" (=1) is selected, the whole image becomes soft and mild. Clearness of characters will be reduced. Normally set to "YES" (=0). SW-C1 No. 8 Reserved Set to "0". SW-D1 No. 1 ~ No. 4 Number of rings for auto receive When the machine is set in the auto receive mode, the number of rings before answering can be selected. It may be set from one to four rings using a binary number. Since the facsimile telephone could be used as an ordinary telephone if the handset is taken off the hook, it should be programmed to the user's choice. If the soft switch was set to 1, direct connection is made to the facsimile. If a facsimile calling beep was heard when the handset is taken off the hook, press the START key and put the handset on the hook to have the facsimile start receiving. If it was set to 0 accidentally, receive ring is set to 1. NOTE: If the machine is set to answer after a large number of rings, it may not be able to receive faxes successfully. If you have difficulty receiving faxes, reduce the number of rings to a maximum of 6. SW-D1 No. 5 Automatic switching manual to auto receive mode This soft switch is used to select whether the machine should switch to the auto receive mode after 5 rings in the manual receive mode or remain in the same way as SW-D1 No. 1, No. 2, No. 3 and No. 4 "0"1"0"1"(5 rings). SW-D1 No. 6 Reserved Set to "0". SW-D1 No. 7, No. 8 CI detect frequency Detection frequency of ring signal for auto reception is set. When set to No. 6=0, No. 7=0, frequency is set to PTT recommendation. When set to No. 6=0, No. 7=1, frequency is set to 11.5Hz or more. When set to No. 6=1, No. 7=0, frequency is set to 13.0Hz or more. When set to No. 6=1, No. 7=1, frequency is set to 20.0Hz or more. SW-D2 No. 1 ~ No. 3 Distinctive ringing setting (PATTERN 4 and 5 are for CANADA only) This function allows reception of services offered by USA and Canada telephone companies in which the customer contracts with the telephone company to have up to 4 telephone numbers (USA) or 6 telephone numbers (Canada) established for one line. Each telephone number is signaled by a different ringing pattern, and the customer can allocate each number to a specific use. Phone Number Intended Purpose Ring Pattern Ring Pattern 555-1234 Voice Calls Standard 555-1235 Facsimile Calls Pattern 1 555-1236 555-1237 Answering Machine PC Modem Pattern 2 Pattern 3 1) USA DISTINCTIVE RING → 1:RING PATTERN 1 → 2:RING PATTERN 2 ↑ ↓ 5:OFF SETTING ← 4:STANDARD RING ← 3:RING PATTERN 3 2) Canada DISTINCTIVE RING → 1:RING PATTERN 1 → 2:RING PATTERN 2 ↑ ↓ 7:OFF SETTING 3:RING PATTERN 3 ↑ ↓ 6:STANDARD RING ← 5:RING PATTERN 5 ← 4:RING PATTERN 4 • Ring Pattern 1 4 5 9 STANDARD has 5 ring patterns, and DISTINCTIVE has 9 patterns. Ring patterns ~ for USA, and ~ for Canada. However, to make the setting procedure as easy as possible for the user to understand these patterns are grouped as follows: 1) RING PATTERN 1 2) RING PATTERN 2 3) RING PATTERN 3 4) RING PATTERN 4 5) RING PATTERN 5 1 RING PATTERN 4 RING PATTERN 5 RING PATTERN 2 RING PATTERN 6 RING PATTERN 3 RING PATTERN 7 RING PATTERN 8 RING PATTERN 9 RING PATTERN for USA for USA for Canada for USA for Canada for USA for Canada for Canada for Canada 6) STANDARD RING 7) OFF SETTING STANDARD RING PATTERN 1 for USA RING PATTERN 2 for USA RING PATTERN 3 for USA RING PATTERN 4 for USA RING PATTERN 5 for CANADA RING PATTERN 6 for CANADA RING PATTERN 7 for CANADA RING PATTERN 8 for CANADA RING PATTERN 9 for CANADA 2S ring 2S ring 4S ring 1.5S ring 2S ring 1S ring 1.5S ring 3S ring 4S ring 0.5S 0.8S 0.5S 0.8S 4S ring 0.4S 0.3S 1S 0.3S 4S ring 0.2S 0.2S 0.4S 0.4S 0.8S 4S ring 0.2S 0.2S 1S 1S 4S ring 1S 1S 1S 4S ring 0.5S 0.5S 1S 0.5S 0.5S 0.5S 0.5S 0.5S 1S 0.5S 0.5S 0.25S 0.25S 0.25S 0.2S 0.2S 0.25S 0.25S 0.2S 6S 2 - 16 manuals4you.com