Sharp A260 Service Manual - Page 23

SW-D2 No. 4 Reserved Set to "0". SW-D2 No. 5 Caller ID function Used for Caller ID function. SW-D2 No. 6 Caller ID detect during CI off Detection of caller ID signal is performed as follows: 0:First CI OFF only 1:All of CI OFF SW-D2 No. 7, No. 8 Reserved Set to "0". SW-D3 No. 1 ~ No. 5 CI off detection timer (0-1550ms setting by 50ms step) Set the minimum time period of CI signal interruption. (Example) A B 400msec 1 2000msec 2 01110 (50ms ~ 14): 700ms (CI interruption>700ms:Judged as a CI OFF section) The section 1 is not judged as a CI OFF section, the CI signal A is counted as one signal. The section 2 is judged as a CI OFF section, the CI signal B is considered as the second signal. 00111 (50ms ~ 7): 350ms (CI interruption>350ms:Judged as a CI OFF section) The section 1 is judged as a CI OFF section, and the CI signal A is counted as two signals. The section 2 is judged as a CI OFF section, and the CI signal B is considered as the third signal. SW-D3 No. 6 ~ No. 8 Reserved Set to "0". SW-E1 No. 1 ~ No. 8 Reserved Set to "0". SW-E2 No. 1 ~ No. 8 Reserved Set to "0". SW-E3 No. 1 ~ No. 8 Reserved Set to "0". SW-F1 No. 1, No. 2 DTMF detect time Used to set detect time of DTMF (Dual Tone Multi Frequency) used in remote reception (5 ). The longer the detect time is, the less the error detection is caused by noises. SW-F1 No. 3 Protection of remote reception (5 Used to set the function of remote reception (5 the remote reception function is disabled. ) detect ). When set to "1", SW-F1 No. 4 Remote reception with GE telephone (Corresponding to TEL made by GE) P. B. X. "1": Compatible with TEL mode by GE "0": Not compatible • When sending (5 ) for remote reception with a GE manufactured telephone remote reception may not take place because of special specifications in their DTMF. To overcome this, a soft SW is provided to change the modem setting to allow for remote reception. • If this soft SW is set to "1", other telephone sets may be adversely affected. UX-A260U SW-F1 No. 5 ~ No. 8 Remote operation code figure by external TEL (0 ~ 9) Remote operation codes can be changed from 0 through 9. If set to greater than 9, it defaults to 9. The "5 " is not changed. Ex-7 (Default: 5 ) SW-F2 No. 1 CNG detection in STAND-BY mode When setting to "1", the CNG signal detection function during stand-by stops. SW-F2 No. 2, No. 3 Number of CNG detect (AM mode) Used for detection of CNG in 1 to 4 pulses. SW-F2 No. 4, No. 5 Number of CNG detect (STAND-BY mode) Used for detection of CNG in 1 to 4 pulses. SW-F2 No. 6 ~ No. 8 Reserved Set to "0". SW-G1 No. 1 ~ No. 8 Reserved Set to "0". SW-G2 No. 1 ~ No. 8 Reserved Set to "0". SW-G3 No. 1 ~ No. 8 Reserved Set to "0". SW-H1 No. 1, No. 2 Busy tone detection ON/OFF time (Lower duration) The initial value of detection is set according to electric condition. The set value is changed according to the local switch board. (Erroneous detection of sound is reduced.) Normally the upper limit is set to 900msec, and the lower limit to 200msec. If erroneous detection is caused by sound, etc., adjust the detection range. The lower limit can be set in the range of 350msec to 150msec. SW-H1 No. 3, No. 4 Busy tone detection ON/OFF time (Upper duration) Similarly to SW-H1 No. 1, the set value can be varied. The upper limit can be set in the range of 650msec to 2700msec. SW-H1 No. 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 SW-H1 No. 2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 SW-H1 No. 3 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 SW-H1 No. 4 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Detection range 150msec ~ 650msec 150msec ~ 900msec 150msec ~ 1500msec 150msec ~ 2700msec 200msec ~ 650msec 200msec ~ 900msec 200msec ~ 1500msec 200msec ~ 2700msec 250msec ~ 650msec 250msec ~ 900msec 250msec ~ 1500msec 250msec ~ 2700msec 350msec ~ 650msec 350msec ~ 900msec 350msec ~ 1500msec 350msec ~ 2700msec 2 - 17