Sharp CD-E500 Service Manual - Page 42

Tracking system check., Check the TE waveform at pin 15 on IC401., Spin

Get Sharp CD-E500 PDF manuals and user guides View all Sharp CD-E500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

CD-E500 CD-E55/E44 (2) Tracking system check. Check the TE waveform at pin 15 on IC401. If the waveform shown in Figure 42-1 appears and soon after NO DISC appears ? Yes No "Initialization" is possible, but play is not possible ? Yes No "Initialization" is not possible. The tracking servo is not activated. Check the peripheral circuits at pins 14, 15 and 20 on IC401, and FC401. A normal jump operation cannot be completed or the beginning of the track cannot be found. Check the around pin 20 on IC401. Data cannot be read. Check the VCO-PLL (Pin73~78 on IC401) system. Stopped CH1=10 V DC 10:1 T CH2=1 V DC 10:1 100 ms/div (100 ms/div) NORM:100 kS/s TE 2 T DRF 1 (3) Spin system check. Press the OPEN/CLOSE switch without inserting a disc, and then try starting the play operation. =Filter= Smoothing : ON BW : FULL =Offset= CH1 : 0.0 V CH2 : 0.00 V CH3 : 0.00 V CH4 : 0.00 V =Record Length= Main : 100 K Zoom : 2 K =Trigger= Mode : NORMAL Type : EDGE CH1 Delay : 2.924 ms Hold off : 0.2 µs Figure 42-1 1. The turntable rotates a little ? (Waveform drawing Figure 42-2) No 2. The turntable doesn't rotate. The spin driver circuit is OK. Yes Check around pin 22 on IC401, pins 10 and 11 on IC402, and CNS402. Stopped CH1=200 mV DC 10:1 T CH2=500 mV DC 10:1 1999/04/07 09:51:15 500 ms/div (500 ms/div) NORM:20 kS/s T FDO 2 SPDO 1 - 42 - =Filter= Smoothing : ON BW : FULL =Offset= CH1 : 0.000 V CH2 : 0.000 V CH3 : 0.00 V CH4 : 0.00 V =Record Length= Main : 100 K Zoom : 2 K =Trigger= Mode : NORMAL Type : EDGE CH2 Delay : 2.924 ms Hold off : 0.2 µs Figure 42-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
CD-E500
CD-E55/E44
– 42 –
T
T
FDO
SPDO
Stopped
CH1=200 mV
DC
10:1
CH2=500 mV
DC
10:1
500 ms/div
1999/04/07
09:51:15
(500 ms/div)
NORM:20 kS/s
2
1
=Record Length=
Smoothing :
ON
CH1
:
0.000 V
CH2
:
0.000 V
Main
:
100 K
Zoom
:
2 K
Mode
:
NORMAL
Type
:
EDGE CH2
Delay
:
2.924 ms
Hold off
:
0.2
μ
s
CH3
:
0.00 V
CH4
:
0.00 V
BW
: FULL
=Trigger=
=Filter=
=Offset=
T
T
TE
DRF
Stopped
CH1=10 V
DC
10:1
CH2=1 V
DC
10:1
100 ms/div
(100 ms/div)
NORM:100 kS/s
2
1
=Record Length=
Smoothing :
ON
CH1
:
0.0 V
CH2
:
0.00 V
Main
:
100 K
Zoom
:
2 K
Mode
:
NORMAL
Type
:
EDGE CH1
Delay
:
2.924 ms
Hold off
:
0.2
μ
s
CH3
:
0.00 V
CH4
:
0.00 V
BW
: FULL
=Trigger=
=Filter=
=Offset=
The tracking servo is not activated.
Check the peripheral circuits at pins 14, 15 and 20 on IC401, and
FC401.
If the waveform shown in Figure 42-1 appears and soon after
NO DISC appears ?
(2) Tracking system check.
Check the TE waveform at pin 15 on IC401.
A normal jump operation cannot be completed or the beginning of
the track cannot be found.
Check the around pin 20 on IC401.
"Initialization" is possible, but play is not possible ?
Data cannot be read. Check the VCO-PLL (Pin73~78 on IC401)
system.
"Initialization" is not possible.
Figure 42-1
Figure 42-2
Press the OPEN/CLOSE switch without inserting a disc, and
then try starting the play operation.
(3) Spin system check.
The spin driver circuit is OK.
1. The turntable rotates a little ?
(Waveform drawing Figure 42-2)
Check around pin 22 on IC401, pins 10 and 11 on IC402, and
CNS402.
2. The turntable doesn't rotate.
No
Yes
No
Yes
Yes
No