Singer 1 One Instruction Manual 34 - Page 24

rolled, hemming

Page 24 highlights

12. How to do rolled hemming This machine can do the 2 types of standard and right looper thread wrapped rolled hem stitching with a seam width of 1.5mm. Always remove the left needle 1. Fabric, needle, thread and stitch length Fabric: Light to medium weight (See page 34) • Rolled hemming is done by rolling the fabric and overedging (seam width 1.5mm), and is not suited for heavy or stiff fabrics. Needle: Singer Cat. No. 2054 #10, #14 Thread: A variety of thread combinations can be used for rolled hemming. Stitch length adjustment (See page 21) For rolled hemming, set the stitch length dial to "2" or "F" and a fine seam can be obtained. 2. How to exchange throat plate M A throat plate for rolled hem stitching has been furnished in the accessories for this machine. By exchanging the ordinary overedge throat plate on the machine with a rolled hemming throat plate by the following procedure, the machine can be used for rolled hem stitching. Rolled hemming throat plate Throat plate screw 1. First of all, always disconnect the power line plug from the receptacle. 2. Turn the hand wheel towards you until the needle is at its highest point. 3. Lift the presser foot. 4. Remove the cylinder cover. (See page 8) 5. Unscrew the throat plate screw (1) and remove the throat plate. 6. Install the rolled hemming throat plate and replace the screw (1). 7. Replace the cylinder cover (see page 8). jj Note: • When replacing the throat plate, be careful that the thread is not caught between the throat plate and machine. • Set seam width to the "M" mark on the rolled hemming throat plate. • To set seam width, align left edge of stationary knife holder with the "M" mark on the rolled hemming throat plate. Be sure the stationary knife is not in contact with the edge of throat plate. Stationa y knife holder 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40

12.
How
to
do
rolled
hemming
This
machine
can
do
the
2
types
of
standard
and
right
looper
thread
wrapped
rolled
hem
stitching
with
a
seam
width
of
1.5mm.
Always
remove
the
left
needle
1.
Fabric,
needle,
thread
and
stitch
length
Fabric:
Light
to
medium
weight
(See
page
34)
Rolled
hemming
is
done
by
rolling
the
fabric
suited
for
heavy
or stiff
fabrics.
Needle:
Singer
Cat.
No.
2054
#10,
#14
Thread:
A
variety
of
thread
combinations
can
be
used
for
rolled
hemming.
Stitch
length
adjustment
(See
page
21)
For
rolled
hemming,
set
the
stitch
length
dial
to
"2"
or
"F"
and
a
fine
seam
can
be
obtained.
2.
How
to
exchange
throat
plate
A
throat
plate
for
rolled
hem
stitching
has
been
furnished
in
the
accessories
for
this
machine.
By
exchanging
the
ordinary
overedge
throat
plate
on
the
machine
with
a
rolled
hemming
throat
plate
by
the
following
procedure,
the
machine
can
be
used
for
rolled
hem
stitching.
1.
First
of
all,
always
disconnect
the
power
line
plug
from
the
receptacle.
2.
Turn
the
hand
wheel
towards
you
until
the
needle
is
at
its
highest
point.
3.
Lift
the
presser
foot.
4.
Remove
the
cylinder
cover.
(See
page
8)
5.
Unscrew
the
throat
plate
screw
(1)
and
remove
the
throat
plate.
6.
Install
the
rolled
hemming
throat
plate
and
replace
the
screw
(1).
7.
Replace
the
cylinder
cover
(see
page
8).
and
overedging
(seam
width
1.5mm),
and
is
not
M
Rolled
hemming
throat
plate
Throat
plate
screw
Note:
When
replacing
the
throat
plate,
be
careful
that
the
thread
is
not
caught
between
the
throat
plate
and
machine.
Set
seam
width
to
the
"M"
mark
on
the
rolled
hemming
throat
plate.
To
set
seam
width,
align
left
edge
of
stationary
knife
holder
with
the
"M"
mark
on
the
rolled
hemming
throat
plate.
Be
sure
the
stationary
knife
is
not
in
contact
with
the
edge
of
throat
plate.
jj
Stationa
y
knife
holder
22