Singer 7258 Stylist Instruction Manual - Page 18

Threading The Bobbin Thread

Get Singer 7258 Stylist PDF manuals and user guides View all Singer 7258 Stylist manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

THREADING THE BOBBIN THREAD 1. Raise the needle to its highest position by rotating the hand 1 wheel toward you (counter-clockwise). 2. Remove the bobbin cover plate by pushing the release button to the right. Bobbin cover will pop up sufficiently to 2 allow you to remove the cover. 3. Insert the bobbin making sure the bobbin rotates counterclockwise when you pull the thread. 3 NOTE: This is a very important step as the bobbin can become unthreaded and cause sewing problems if it rotates clockwise. 4. Pull thread through the slot (A) and then to the left. 4 A 5. With a finger held gently on top of the bobbin, pull the thread until it stops in slot (B). Then pull about 6" (15 cm) 5 of thread and lead it towards back of the machine under the presser foot. NOTE: This is also a very important step to assure the bobbin thread does not slip out of position. B A 6. Replace the bobbin cover plate onto the needle plate. 6 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
18
2
3
4
5
6
1
THREADING THE BOBBIN THREAD
1. Raise the needle to its highest position by rotating the hand
wheel toward you (counter-clockwise).
2. Remove the bobbin cover plate by pushing the release
button to the right. Bobbin cover will pop up sufficiently to
allow you to remove the cover.
3. Insert the bobbin making sure the bobbin rotates counter-
clockwise when you pull the thread.
4. Pull thread through the slot (A) and then to the left.
5. With a finger held gently on top of the bobbin, pull the
thread until it stops in slot (B). Then pull about 6" (15 cm)
of thread and lead it towards back of the machine under
the presser foot.
6. Replace the bobbin cover plate onto the needle plate.
A
A
B
NOTE: This is also a very important step to assure
the bobbin thread does not slip out of position.
NOTE: This is a very important step as the bobbin
can become unthreaded and cause sewing problems
if it rotates clockwise.