Snapper 200Z Operater's Manual - Page 23

Adjustments and Service

Get Snapper 200Z PDF manuals and user guides View all Snapper 200Z manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

A B Adjustments and Service Figure 13. Seat Adjustment Seat Adjustments r n The seat and ground speed levers should be adjusted fo tio so that operator's elbows are supported by the arm rests when his/her hands are on the controls, and the ground speed levers can be moved through their full range of t c motion without contacting the operator's legs. o Seat Position Adjustment u Lift the seat adjustment lever (A, Figure 13). Slide the N d seat forward or backward to the desired position, then lower the seat adjustment lever. Make sure the lever o locks into the locking slots (B) in the seat base. pr Ground Speed Lever Adjustment e Remove the ground speed lever mounting hardware (Figure 14) and reposition the lever either up or down R from its original position. Replace the hardware. Figure 14. Ground Speed Lever Adjustments Speed Balancing Adjustment If the rider drifts to the right or left when the ground speed levers are in the maximum forward position, the top speed of each of these levers can be balanced. Only adjust the speed of the wheel that is traveling faster. To Reduce the Speed of the Faster Wheel 1. Loosen the bolt securing the forward adjust plate (Figure 14). 2. Slide the plate up approximately 1/8". 3. Retighten the bolt and recheck speed balance. 4. Repeat steps 1-3 until adjustment is complete. WARNING DO NOT adjust the rider for a faster overall speed forward or reverse than it was designed. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
23
Adjustments and Service
Seat Adjustments
The seat and ground speed levers should be adjusted
so that operator’s elbows are supported by the arm rests
when his/her hands are on the controls, and the ground
speed levers can be moved through their full range of
motion without contacting the operator’s legs.
Seat Position Adjustment
Lift the seat adjustment lever (
A
, Figure 13). Slide the
seat forward or backward to the desired position, then
lower the seat adjustment lever. Make sure the lever
locks into the locking slots (
B
) in the seat base.
Ground Speed Lever Adjustment
Remove the ground speed lever mounting hardware
(Figure 14) and reposition the lever either up or down
from its original position. Replace the hardware.
Figure 13.
Seat Adjustment
Figure 14.
Ground Speed Lever Adjustments
Speed Balancing Adjustment
If the rider drifts to the right or left when the ground
speed levers are in the maximum forward position, the
top speed of each of these levers can be balanced. Only
adjust the speed of the wheel that is traveling faster.
To Reduce the Speed of the Faster Wheel
1. Loosen the bolt securing the forward adjust plate
(Figure 14).
2. Slide the plate up approximately 1/8”.
3. Retighten the bolt and recheck speed balance.
4. Repeat steps 1-3 until adjustment is complete.
WARNING
DO NOT adjust the rider for a faster overall speed
forward or reverse than it was designed.
A
B
Not for
Reproduction