Sony DCR-HC52 Operating Guide - Page 64

Video head, LCD screen

Get Sony DCR-HC52 - Handycam Camcorder - 680 KP PDF manuals and user guides
UPC - 027242727427
View all Sony DCR-HC52 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Maintenance and precautions (Continued) • The warning message does not appear when the power is turned on. • Neither % or Z flash when a cassette is inserted and video operation buttons are touched. If moisture starts to condense, your camcorder sometimes cannot detect condensation. If this happens, the cassette is sometimes not ejected for 10 seconds after the cassette lid is opened. This is not a malfunction. Do not close the cassette lid until the cassette is ejected. x Note on moisture condensation Moisture may condense when you bring your camcorder from a cold place into a warm place (or vice versa) or when you use your camcorder in a humid place as shown below. • When you bring your camcorder from a ski slope into a place warmed up by a heating device. • When you bring your camcorder from an air conditioned car or room into a hot place outside. • When you use your camcorder after a squall or a shower. • When you use your camcorder in a hot and humid place. x How to avoid moisture condensation When you bring your camcorder from a cold place into a warm place, put your camcorder in a plastic bag and seal it tightly. Remove the bag when the air temperature inside the plastic bag has reached the surrounding temperature (after about one hour). Video head It is recommended you use a cleaning cassette (optional) before recording anything important. • If the video heads are dirty, video or sound distortion may be apparent. • If the following problem occurs, clean the video heads for 10 seconds with the Sony DVM12CLD cleaning cassette (optional). - Mosaic-pattern noise appears on the playback picture or the screen is displayed in blue. 64 - Playback pictures do not move. - Playback pictures do not appear or the sound breaks off. - [x Dirty video head. Use a cleaning cassette.] appears on the screen during recording/playback. • The video heads will wear after long use. If you cannot obtain a clear image even after using a cleaning cassette (optional), it might be because the video heads are worn. Please contact your Sony dealer or local authorized Sony service facility to have the video heads replaced. LCD screen • Do not exert excessive pressure on the LCD screen, as it may cause damage. • If your camcorder is used in a cold place, a residual image may appear on the LCD screen. This is not a malfunction. • While using your camcorder, the back of the LCD screen may heat up. This is not a malfunction. x To clean the LCD screen If fingerprints or dust make the LCD screen dirty, it is recommended you use a soft cloth to clean it. When you use the LCD Cleaning Kit (optional), do not apply the cleaning liquid directly to the LCD screen. Use cleaning paper moistened with the liquid. x On adjustment of the touch panel (CALIBRATION) The buttons on the touch panel may not work correctly. If this happens, follow the procedure below. It is recommended you connect your camcorder to the wall outlet (wall socket) using the supplied AC Adaptor during the operation. 1 Turn off the power, then slide the POWER switch repeatedly to turn on the PLAY/ EDIT lamp while pressing DISP/BATT INFO on your camcorder, and keep pressing down DISP/BATT INFO for about 5 seconds.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
64
•
The warning message does not appear when the
power is turned on.
• Neither
%
or
Z
flash when a cassette is inserted
and video operation buttons are touched.
If moisture starts to condense, your
camcorder sometimes cannot detect
condensation. If this happens, the cassette is
sometimes not ejected for 10 seconds after
the cassette lid is opened. This is not a
malfunction. Do not close the cassette lid
until the cassette is ejected.
x
Note on moisture condensation
Moisture may condense when you bring
your camcorder from a cold place into a
warm place (or vice versa) or when you use
your camcorder in a humid place as shown
below.
•
When you bring your camcorder from a ski
slope into a place warmed up by a heating
device.
•
When you bring your camcorder from an air
conditioned car or room into a hot place outside.
•
When you use your camcorder after a squall or a
shower.
•
When you use your camcorder in a hot and
humid place.
x
How to avoid moisture condensation
When you bring your camcorder from a
cold place into a warm place, put your
camcorder in a plastic bag and seal it
tightly. Remove the bag when the air
temperature inside the plastic bag has
reached the surrounding temperature (after
about one hour).
Video head
It is recommended you use a cleaning
cassette (optional) before recording
anything important.
•
If the video heads are dirty, video or sound
distortion may be apparent.
•
If the following problem occurs, clean the video
heads for 10 seconds with the Sony DVM-
12CLD cleaning cassette (optional).
–
Mosaic-pattern noise appears on the playback
picture or the screen is displayed in blue.
–
Playback pictures do not move.
–
Playback pictures do not appear or the sound
breaks off.
–[
x
Dirty video head. Use a cleaning
cassette.] appears on the screen during
recording/playback.
•
The video heads will wear after long use. If you
cannot obtain a clear image even after using a
cleaning cassette (optional), it might be because
the video heads are worn. Please contact your
Sony dealer or local authorized Sony service
facility to have the video heads replaced.
LCD screen
•
Do not exert excessive pressure on the LCD
screen, as it may cause damage.
•
If your camcorder is used in a cold place, a
residual image may appear on the LCD screen.
This is not a malfunction.
•
While using your camcorder, the back of the
LCD screen may heat up. This is not a
malfunction.
x
To clean the LCD screen
If fingerprints or dust make the LCD screen
dirty, it is recommended you use a soft
cloth to clean it. When you use the LCD
Cleaning Kit (optional), do not apply the
cleaning liquid directly to the LCD screen.
Use cleaning paper moistened with the
liquid.
x
On adjustment of the touch panel
(CALIBRATION)
The buttons on the touch panel may not
work correctly. If this happens, follow the
procedure below. It is recommended you
connect your camcorder to the wall outlet
(wall socket) using the supplied AC
Adaptor during the operation.
1
Turn off the power, then slide the POWER
switch repeatedly to turn on the PLAY/
EDIT lamp while pressing DISP/BATT
INFO on your camcorder, and keep
pressing down DISP/BATT INFO for
about 5 seconds.
Maintenance and precautions (Continued)