Sony DCR-HC52 Operating Guide - Page 65

On handling the casing, About care and storage of the lens, To remove dust from inside the, viewfinder

Get Sony DCR-HC52 - Handycam Camcorder - 680 KP PDF manuals and user guides
UPC - 027242727427
View all Sony DCR-HC52 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

2 Touch the "×" displayed on the screen with the corner of the "Memory Stick" or the like. The position of the "×" changes. If you did not press the right spot, start from step 2 again. • You cannot calibrate the LCD screen if it is rotated. On handling the casing • If the casing is soiled, clean the camcorder body with a soft cloth lightly moistened with water, and then wipe the casing with a dry soft cloth. • Avoid the following to avoid damage to the finish. - Using chemicals such as thinner, benzine, alcohol, chemical cloths, repellent, insecticide and sunscreen. - Handling with above substances on your hands. - Leaving the casing in contact with rubber or vinyl objects for a long period of time. About care and storage of the lens • Wipe the surface of the lens clean with a soft cloth in the following instances: - When there are fingerprints on the lens surface. - In hot or humid locations - When the lens is exposed to salty air such as at the seaside. • Store in a well-ventilated location subject to little dirt or dust. • To prevent mold, periodically clean the lens as described above. It is recommended that you operate your camcorder about once a month to keep it in optimum state for a long time. To remove dust from inside the viewfinder 1 Pull out the viewfinder. 2 While pushing in the tab on the side with a fine-tipped implement such as a ball point pen, pull the eyecup block in the direction of the arrow to remove. Tab 3 Remove dust from the eyecup block with a camera blower, etc. 4 Press the viewfinder onto the body of the camcorder. 5 Remove dust from the inside area where the eyecup block was attached with a camera blower, etc. Additional Information Continued , 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
65
Additional Information
2
Touch the “×” displayed on the screen with
the corner of the “Memory Stick” or the
like.
The position of the “×” changes. If you did
not press the right spot, start from step
2
again.
•
You cannot calibrate the LCD screen if it is
rotated.
On handling the casing
•
If the casing is soiled, clean the camcorder body
with a soft cloth lightly moistened with water,
and then wipe the casing with a dry soft cloth.
•
Avoid the following to avoid damage to the
finish.
–
Using chemicals such as thinner, benzine,
alcohol, chemical cloths, repellent, insecticide
and sunscreen.
–
Handling with above substances on your
hands.
–
Leaving the casing in contact with rubber or
vinyl objects for a long period of time.
About care and storage of the lens
•
Wipe the surface of the lens clean with a soft
cloth in the following instances:
–
When there are fingerprints on the lens
surface.
–
In hot or humid locations
–
When the lens is exposed to salty air such as
at the seaside.
•
Store in a well-ventilated location subject to
little dirt or dust.
•
To prevent mold, periodically clean the lens as
described above. It is recommended that you
operate your camcorder about once a month to
keep it in optimum state for a long time.
To remove dust from inside the
viewfinder
1
Pull out the viewfinder.
2
While pushing in the tab on the side
with a fine-tipped implement such as a
ball point pen, pull the eyecup block in
the direction of the arrow to remove.
3
Remove dust from the eyecup block
with a camera blower, etc.
4
Press the viewfinder onto the body of
the camcorder.
5
Remove dust from the inside area where
the eyecup block was attached with a
camera blower, etc.
Tab
Continued
,