Sony MXD-D5C Operating Instructions - Page 25

Recording the Current CD Track (REC-IT Function), To change the trigger level for Track

Get Sony MXD-D5C PDF manuals and user guides View all Sony MXD-D5C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Recording on MDs Set "T.Mark" in Setup Menu to "LSyn" or "Off" as follows: 1 Press MENU/NO twice to display "Setup Menu" while the deck is stopped. 2 Turn AMS to select "T.Mark LSyn," then press AMS. 3 Turn AMS to select "T.Mark LSyn" or "T.Mark Off," then press AMS. If you select "T.Mark LSyn," "L.SYNC" lights up in the display. 4 Press MENU/NO. To change the trigger level for Track Marking Function Do the procedure below to change the signal level that triggers Track Marking Function. 1 Press MENU/NO twice to display "Setup Menu" while the deck is stopped. 2 Turn AMS to display "LS(T)", then press AMS. 3 Turn AMS to select the level, then press AMS. You can set the level at any value between -72 dB and 0 dB, in 2 dB increments. 4 Press MENU/NO. Note If you turn off the deck or disconnect the AC power cord, the deck will recall the last setting of the track marking function ("LSyn" or "Off") and the trigger level the next time you turn on the deck. Recording the Current CD Track (REC-IT Function) You can record specific tracks on a CD while listening to them. This function allows you to put only the tracks you like onto the MD. When using the remote, set SELECT to CD. · REC-IT 1 Press · on the CD player section. Make sure that the MD deck section is stopped. 2 Press REC-IT when you hear a track you want to record. Play returns to the start of the track and recording starts. The recording stops at the end of the track, but CD playback continues from the next track. To stop recording Press p on the CD player section. Notes • You cannot record over existing material during REC-IT Recording. The deck automatically starts recording from the end of the existing material. • Make sure that the remaining recordable time on the MD is longer than the playing time of the CD track. • The recording level specified in the Setup Menu (page 23) is not applied during REC-IT Recording. The initial reference level (0.0 dB) is used instead. While "TOC Writing" is flashing Do not move the deck or pull out the AC power cord to ensure the complete recording. The deck is currently updating the Table Of Contents (TOC) of the MD. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
25
Recording on MDs
Set “T.Mark” in Setup Menu to “LSyn” or “Off” as
follows:
1
Press MENU/NO twice to display “Setup Menu”
while the deck is stopped.
2
Turn AMS to select “T.Mark LSyn,” then press
AMS.
3
Turn AMS to select “T.Mark LSyn” or “T.Mark
Off,” then press AMS.
If you select “T.Mark LSyn,” “L.SYNC” lights up
in the display.
4
Press MENU/NO.
To change the trigger level for Track
Marking Function
Do the procedure below to change the signal level that
triggers Track Marking Function.
1
Press MENU/NO twice to display “Setup Menu”
while the deck is stopped.
2
Turn AMS to display “LS(T)”, then press AMS.
3
Turn AMS to select the level, then press AMS.
You can set the level at any value between –72 dB
and 0 dB, in 2 dB increments.
4
Press MENU/NO.
Note
If you turn off the deck or disconnect the AC power cord, the
deck will recall the last setting of the track marking function
(“LSyn” or “Off”) and the trigger level the next time you
turn on the deck.
Recording the Current CD Track
(REC-IT Function)
You can record specific tracks on a CD while listening
to them. This function allows you to put only the tracks
you like onto the MD.
When using the remote, set SELECT to CD.
·
REC-IT
1
Press
·
on the CD player section.
Make sure that the MD deck section is stopped.
2
Press REC-IT when you hear a track you want to
record.
Play returns to the start of the track and recording
starts.
The recording stops at the end of the track,
but CD playback continues from the next track.
To stop recording
Press
p
on the CD player section.
Notes
•
You cannot record over existing material during REC-IT
Recording.
The deck automatically starts recording from
the end of the existing material.
•
Make sure that the remaining recordable time on the MD
is longer than the playing time of the CD track.
•
The recording level specified in the Setup Menu (page 23)
is not applied during REC-IT Recording. The initial
reference level (0.0 dB) is used instead.
While
“
TOC Writing
”
is flashing
Do not move the deck or pull out the AC power cord to
ensure the complete recording.
The deck is currently
updating the Table Of Contents (TOC) of the MD.