Sony MZ-N910 Help - Page 21

Remove the MD, Press, Recording, condition, REC LED

Get Sony MZ-N910 PDF manuals and user guides View all Sony MZ-N910 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Note If you record on a previously recorded disc, the recorder is factory set to overwrite the entire contents of the disc. If you want the recording to start after the existing contents, do the procedure "Recording without overwriting existing material" (page 59) before doing step 3, "Record an MD." (page 20). To Record from the end of the current contents1) Record over previous material from a point partway through1) Pause Remove the MD Press Press END SEARCH, and then press and slide REC.1) Press N, or press ., or > to find the start point of recording, and then press x to stop. Then press and slide REC. Press X.2) Press X again to resume recording. Press x and open the lid.3) (The lid does not open while "TOC Edit" flashing in the display.) 1) If "REC-Posi" is set to "From End", recording operations will always start from the end of the previously recorded material without pressing the END SEARCH button (page 59). 2) A track mark is added at the point where you press X again to resume recording while pausing; thus the remainder of the track will be counted as a new track. 3) If you open the lid while "REC-Posi" is set to "From Here", recording will begin from the top of the disc the next time you record. Check the point to start recording on the display. If the recording does not start • Make sure the recorder is not locked (pages 12, 17). • Make sure the MD is not record-protected (pages 19, 74). • Premastered MDs cannot be recorded over. To know the recording condition The REC LED lights up or flashes according to the recording condition. Recording condition REC LED While recording lights up flashes according to the loudness of the source while recording with a microphone (voice mirror) Recording standby flashes Less than 3 flashes slowly minutes' recording time available A track mark has goes off been added1) momentarily While checking-out flashes faster 1) Except when track marking was done manually or automatically using Auto Time Mark (page 30). 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
21
Note
If you record on a previously recorded disc, the recorder is factory set to overwrite the entire contents of
the disc. If you want the recording to start after the existing contents, do the procedure “Recording
without overwriting existing material” (page 59) before doing step 3, “Record an MD.” (page 20).
If the recording does not start
•
Make sure the recorder is not locked (pages
12, 17).
•
Make sure the MD is not record-protected
(pages 19, 74).
•
Premastered MDs cannot be recorded over.
To know the recording
condition
The REC LED lights up or flashes
according to the recording condition.
To
Press
Record from the end of the
current contents
1)
1)
If “REC-Posi” is set to “From End”, recording operations will always start from the end of the
previously recorded material without pressing the END SEARCH button (page 59).
Press END SEARCH, and then press and slide REC.
1)
Record over previous
material from a point
partway through
1)
Press
N
, or press
.
, or
>
to find the start point of
recording, and then press
x
to stop. Then press and slide
REC.
Pause
Press
X
.
2)
Press
X
again to resume recording.
2)
A track mark is added at the point where you press
X
again to resume recording while pausing; thus
the remainder of the track will be counted as a new track.
Remove the MD
Press
x
and open the lid.
3)
(The lid does not open while
“TOC Edit” flashing in the display.)
3)
If you open the lid while “REC-Posi” is set to “From Here”, recording will begin from the top of the
disc the next time you record. Check the point to start recording on the display.
Recording
condition
REC LED
While recording
lights up
flashes according
to the loudness of
the source while
recording with a
microphone
(voice mirror)
Recording standby
flashes
Less than 3
minutes’ recording
time available
flashes slowly
A track mark has
been added
1)
1)
Except when track marking was done
manually or automatically using Auto Time
Mark (page 30).
goes off
momentarily
While checking-out
flashes faster