Sony STRDH830 Operating Instructions - Page 36

To cancel Auto Calibration, When Error Code appears, Checking the Auto Calibration, results - remote code

Get Sony STRDH830 PDF manuals and user guides View all Sony STRDH830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

7 Press V/v repeatedly to select the item you want, then press . • Retry: Performs the Auto Calibration again. • Save: Save the measurement results and exits the setting process. • Warning: Displays warning related to the measurement results. See "Message list after Auto Calibration measurement" (page 37). • Exit: Exits the setting process without saving the measurement results. 8 Save the measurement result. Select "Save" in step 7. Note You can select the calibration type you want by using the "Custom" Auto Calibration (page 37). 9 Disconnect the optimizer microphone from the receiver. Note If you reposition your speaker, we recommend that you perform Auto Calibration again to enjoy the surround sound. Tips • You can change the unit of distance in "Distance Unit" in the Speaker Settings menu (page 65). • The size of a speaker ("Large"/"Small") is determined by the low frequency characteristics. The measurement results may vary, depending on the position of the optimizer microphone and speakers, and the shape of the room. It is recommended that you apply the measurement results. However, you can change those settings in the Speaker Settings menu. Save the measurement results first, then try to change the settings. To cancel Auto Calibration The Auto Calibration function will be canceled when you perform the following during the measurement process: - Press ?/1. - Press the input buttons on the remote control or turn the INPUT SELECTOR on the receiver. - Press MUTING or . - Press SPEAKERS on the receiver. - Change the volume level. - Connect the headphones. - Press SHIFT, then press AUTO CAL again. Checking the Auto Calibration results To check error code or warning message obtained in "Performing Auto Calibration" (page 35), proceed with the following steps. Press V/v to select "Warning" in step 7 in "Performing Auto Calibration" (page 35) then press . If a warning message appears, check the message and use the receiver without change. Or if necessary, perform Auto Calibration again. When "Error Code" appears Check the error and perform Auto Calibration again. 1 Press to select "ENTER". "RETRY ?" appears on the TV screen. 2 Press B/b to select "YES", then press . 3 Repeat step 6 to 9 in "Performing Auto Calibration" (page 35). 36GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
36
GB
7
Press
V
/
v
repeatedly to select
the item you want, then press
.
•
Retry:
Performs the Auto Calibration
again.
•
Save:
Save the measurement results and
exits the setting process.
•
Warning:
Displays warning related to
the measurement results. See “Message
list after Auto Calibration
measurement” (page 37).
•
Exit:
Exits the setting process without
saving the measurement results.
8
Save the measurement result.
Select “Save” in step 7.
Note
You can select the calibration type you want by
using the “Custom” Auto Calibration
(page 37).
9
Disconnect the optimizer
microphone from the receiver.
Note
If you reposition your speaker, we recommend that
you perform Auto Calibration again to enjoy the
surround sound.
Tips
• You can change the unit of distance in “Distance
Unit” in the Speaker Settings menu (page 65).
• The size of a speaker (“Large”/“Small”) is
determined by the low frequency characteristics.
The measurement results may vary, depending on
the position of the optimizer microphone and
speakers, and the shape of the room. It is
recommended that you apply the measurement
results. However, you can change those settings in
the Speaker Settings menu. Save the measurement
results first, then try to change the settings.
To cancel Auto Calibration
The Auto Calibration function will be
canceled when you perform the following
during the measurement process:
– Press
?
/
1
.
–
Press the input buttons on the remote control
or turn the INPUT SELECTOR on the
receiver.
– Press MUTING or
.
– Press SPEAKERS on the receiver.
– Change the volume level.
– Connect the headphones.
– Press SHIFT, then press AUTO CAL again.
To check error code or warning message
obtained in “Performing Auto Calibration”
(page 35), proceed with the following steps.
Press
V
/
v
to select “Warning” in
step 7 in “Performing Auto
Calibration” (page 35) then press
.
If a warning message appears, check the
message and use the receiver without change.
Or if necessary, perform Auto Calibration
again.
When “Error Code” appears
Check the error and perform Auto Calibration
again.
1
Press
to select “ENTER”.
“RETRY ?” appears on the TV screen.
2
Press
B
/
b
to select “YES”, then press
3
Repeat step 6 to 9 in “Performing Auto
Calibration” (page 35).
Checking the Auto Calibration
results