Stihl MS 193 C-E Product Instruction Manual - Page 24

D =Felling Cut, WARNING, E = Hinge, Felling Cut for Small Diameter Trees, Simple Fan Cut

Get Stihl MS 193 C-E PDF manuals and user guides View all Stihl MS 193 C-E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

English D =Felling Cut E = Hinge E D Felling Cut for Small Diameter Trees: Simple Fan Cut D E 001BA144 KN 001BA145 KN 001BA147 KN Conventional and open-face technique: N Begin 1 to 2 inches (2,5 to 5 cm) higher than center of felling notch. N Cut horizontally towards the felling notch. N Leave approx.1/10 of diameter uncut. This is the hinge. N Do not cut through the hinge - you could lose control of the direction of the fall. Drive wedges into the felling cut where necessary to control the fall. WARNING If the tip of the bar contacts a wedge, it may cause kickback. Wedges should be of wood or plastic - never steel, which can damage the chain. N Helps control the falling tree. N Do not cut through the hinge - you could lose control of the direction of the fall. Engage the bumper spikes of the chain saw directly behind the location of the intended hinge and pivot the saw around this point only as far as the hinge. The bumper spike rolls against the trunk. 22 MS 193 C

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
MS 193 C
English
22
D =Felling Cut
Conventional and open-face technique:
N
Begin 1 to 2 inches (2,5 to 5 cm)
higher than center of felling notch.
N
Cut horizontally towards the felling
notch.
N
Leave approx.1/10 of diameter
uncut. This is the hinge.
N
Do not cut through the hinge – you
could lose control of the direction of
the fall.
Drive wedges into the felling cut where
necessary to control the fall.
WARNING
If the tip of the bar contacts a wedge, it
may cause kickback. Wedges should be
of wood or plastic – never steel, which
can damage the chain.
E = Hinge
N
Helps control the falling tree.
N
Do not cut through the hinge – you
could lose control of the direction of
the fall.
Felling Cut for Small Diameter Trees:
Simple Fan Cut
Engage the bumper spikes of the chain
saw directly behind the location of the
intended hinge and pivot the saw around
this point only as far as the hinge. The
bumper spike rolls against the trunk.
001BA144 KN
D
D
001BA145 KN
E
E
001BA147 KN