Stihl MS 193 C-E Product Instruction Manual - Page 36

Starting / Stopping the, Engine

Get Stihl MS 193 C-E PDF manuals and user guides View all Stihl MS 193 C-E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

English Starting / Stopping the Engine Positions of Choke Shutter trigger at the same time and hold them in that position - now set the Master Control lever. The Master Control lever moves from the starting throttle position (n) to the run position (F) when you press down the throttle trigger lockout and blip the throttle trigger at the same time. To switch off the engine, move the Master Control lever to Stop (0). Manual fuel pump On the ground 418BA016 KN 418BA005 KN Choke shutter closed l - for starting the engine Select this position: - if the engine is cold - if the engine stalls when you open the throttle after starting. - if the fuel tank was run until empty (engine stopped). Choke shutter open j - for starting the engine Select this position: - if the engine is warm, i.e. if it has been running for about one minute. - When the engine begins to fire - after clearing a flooded combustion chamber. Setting the Master Control Lever The manual fuel pump bulb must be pressed: - When starting for the first time. - if the fuel tank was run until empty (engine stopped). Holding the Saw There are two ways of holding the saw when starting. N Place your saw on the ground. Make sure you have a firm footing - check that the chain is not touching any object or the ground. N Hold the saw firmly on the ground with your left hand on the front handle - your thumb should be under the handle. N Put your right foot into the rear handle and press down. To move the Master Control lever from the normal run position (F) to starting throttle (n), press down the throttle trigger lockout and squeeze the throttle 34 MS 193 C

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
MS 193 C
English
34
Positions of Choke Shutter
Choke shutter closed
l
– for starting
the engine
Select this position:
–
if the engine is cold
–
if the engine stalls when you open
the throttle after starting.
–
if the fuel tank was run until empty
(engine stopped).
Choke shutter open
j
– for starting the
engine
Select this position:
–
if the engine is warm, i.e. if it has
been running for about one minute.
–
When the engine begins to fire
–
after clearing a flooded combustion
chamber.
Setting the Master Control Lever
To move the Master Control lever from
the normal run position (
F
) to starting
throttle (
n
), press down the throttle
trigger lockout and squeeze the throttle
trigger at the same time and hold them in
that position – now set the Master
Control lever.
The Master Control lever moves from
the starting throttle position (
n
) to the
run position (
F
) when you press down
the throttle trigger lockout and blip the
throttle trigger at the same time.
To switch off the engine, move the
Master Control lever to Stop (
0
).
Manual fuel pump
The manual fuel pump bulb must be
pressed:
–
When starting for the first time.
–
if the fuel tank was run until empty
(engine stopped).
Holding the Saw
There are two ways of holding the saw
when starting.
On the ground
N
Place your saw on the ground.
Make sure you have a firm footing –
check that the chain is not touching
any object or the ground.
N
Hold the saw firmly on the ground
with your left hand on the front
handle – your thumb should be
under the handle.
N
Put your right foot into the rear
handle and press down.
Starting / Stopping the
Engine
418BA016 KN
418BA005 KN