TP-Link EAP115-Wall EAP115EU-Wall V1 User Guide - Page 41

Client, LAN Traffic

Get TP-Link EAP115-Wall PDF manuals and user guides View all TP-Link EAP115-Wall manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

LAN Port1/ Displays the maximum transmission rate and duplex mode (half-duplex LAN Port2: or full-duplex) of the port.  Client Figure 6-6 Client MAC: Displays the MAC address of the client of the AP selected in AP List. SSID: Displays the SSID the client is connected to. SNR(dB): Signal to Noise Ratio, the power ratio between the received wireless signal strength and the environmental noise strength. The bigger the value of SNR is, the better network performance the device provides. CCQ(%): Displays the wireless Client Connection Quality (CCQ). CCQ refers to the ratio of current effective transmission bandwidth and the theoretically maximum available bandwidth. CCQ reflects the actual link condition. Rate(Mbps): Displays the data rate at which the client transmits wireless packets. Down(Byte): Displays the throughput of the downstream data. Up(Byte): Displays the throughput of the upstream data. Active Time: Displays the amount of time the client has been connected to the device.  LAN Traffic Click LAN Traffic and you can monitor the data transmission status of the LAN port. Figure 6-7 LAN Traffic Rx/Tx Packets: Displays the total amount of packets received/sent on the LAN port. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
38
LAN
Port1/
LAN Port2:
Displays the maximum transmission rate and duplex mode (half-duplex
or full-duplex) of the port.
Client
Figure 6-6 Client
MAC:
Displays the MAC address of the client of the AP selected in
AP List
.
SSID:
Displays the SSID the client is connected to.
SNR(dB):
Signal to Noise Ratio, the power ratio between the received wireless signal
strength and the environmental noise strength. The bigger the value of SNR
is, the better network performance the device provides.
CCQ(%):
Displays the wireless Client Connection Quality (CCQ). CCQ refers to the
ratio of current effective transmission bandwidth and the theoretically
maximum available bandwidth. CCQ reflects the actual link condition.
Rate(Mbps):
Displays the data rate at which the client transmits wireless packets.
Down(Byte):
Displays the throughput of the downstream data.
Up(Byte):
Displays the throughput of the upstream data.
Active Time:
Displays the amount of time the client has been connected to the device.
LAN Traffic
Click
LAN Traffic
and you can monitor the data transmission status of the LAN port.
Figure 6-7 LAN Traffic
Rx/Tx Packets:
Displays the total amount of packets received/sent on the LAN port.