TRENDnet TEW-823DRU User's Guide - Page 43

Allow remote access to your router management Add static routes, Remote Control via Internet

Get TRENDnet TEW-823DRU PDF manuals and user guides View all TRENDnet TEW-823DRU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

TRENDnet User's Guide Allow remote access to your router management page Advanced > Setup > Management You may want to make changes to your router from a remote location such at your office or another location while away from your home. 1. Log into your router management page (see "Access your router management page" on page 9). 2. Click on Advanced and click Setup, then click on Management. 3. Review the setting on the Remote Management section. Click Apply to save settings • Remote Control (via Internet): Click the drop-down list and select Enable to enable remote management or Disable to disable remote management. • Remote Port: Enter the port to assign remote access to the router. It is recommended to leave this setting as 8080. Note: If you have configured port 8080 for another configuration section such as virtual server or special application, please change the port to use. (Recommended port range 1024-65534) TEW-823DRU Add static routes Advanced > Setup > Routing You may want set up your router to route computers or devices on your network to other local networks through other routers. Generally, different networks can be determined by the IP addressing assigned to those networks. Generally speaking and for the case of an example, your network may have 192.168.10.x IP addressing and another network may have 192.168.20.x IP addressing and because the IP addressing of these two networks are different, they are separate networks. In order to communicate between the two separate networks, static routing needs to be configured. Below is an example diagram where routing is needed for devices and computers on your network to access the other network. Note: Configuring this feature assumes that you have some general networking knowledge. 1. Log into your router management page (see "Access your router management page" on page 9). 2. Click on Advanced and click on Setup, then click on Routing. 3. Review the Routing section. Click Add to save settings. • Destination IP Address: Enter the IP network address of the destination network for the route. (e.g. 192.168.20.0) • Destination IP Netmask: Enter the subnet mask of the destination network for the route.(e.g. 255.255.255.0) • Gateway: Enter the gateway to the destination network for the route. (e.g. 192.168.10.2) • Metric: Enter the metric or priority of the route. The metric range is 1-15, the lowest number 1 being the highest priority. (e.g. 1 ) • Interface - Select the interface to assign the route. © Copyright 2014 TRENDnet. All Rights Reserved. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
© Copyright 2014 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-823DRU
40
Allow remote access to your router management page
Advanced > Setup > Management
You may want to make changes to your router from a remote location such at your
office or another location while away from your home.
1. Log into your router management page (see “
Access your router management page
”
on page 9).
2. Click on
Advanced
and click
Setup
, then click on
Management
.
3. Review the setting on the
Remote Management
section. Click
Apply
to save settings
•
Remote Control (via Internet):
Click the drop-down list and select
Enable
to
enable remote management or
Disable
to disable remote management.
•
Remote Port:
Enter the port to assign remote access to the router. It is
recommended to leave this setting as 8080.
Note:
If you have configured port 8080 for another configuration section such as
virtual server or special application, please change the port to use.
(Recommended port range 1024-65534)
Add static routes
Advanced > Setup > Routing
You may want set up your router to route computers or devices on your network to
other local networks through other routers. Generally, different networks can be
determined by the IP addressing assigned to those networks. Generally speaking and for
the case of an example, your network may have 192.168.10.x IP addressing and another
network may have 192.168.20.x IP addressing and because the IP addressing of these
two networks are different, they are separate networks. In order to communicate
between the two separate networks, static routing needs to be configured. Below is an
example diagram where routing is needed for devices and computers on your network
to access the other network.
Note:
Configuring this feature assumes that you have some general networking
knowledge.
1. Log into your router management page (see “
Access your router management page
”
on page 9).
2. Click on
Advanced
and click on
Setup
, then click on
Routing
.
3. Review the Routing section. Click
Add
to save settings.
•
Destination IP Address:
Enter the IP network address of the destination network
for the route. (e.g.
192.168.20.0
)
•
Destination IP Netmask:
Enter the subnet mask of the destination network for
the route.(e.g.
255.255.255.0
)
•
Gateway:
Enter the gateway to the destination network for the route.
(e.g.
192.168.10.2
)
•
Metric:
Enter the metric or priority of the route. The metric range is
1-15
, the
lowest number
1
being the highest priority. (e.g.
1
)
•
Interface
– Select the interface to assign the route.