Toshiba TDP-XP1 User Manual - Page 25

Operations, Turning the power off, Press the ON/STANDBY button. - fan

Get Toshiba TDP-XP1 PDF manuals and user guides View all Toshiba TDP-XP1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

■ Turning the power off 1 Press the ON/STANDBY button. A message appears on the screen, confirming that you wish to shut off the power. To shut off the power, press the ON/STANDBY button again. If you do not wish to shut off the power, wait for a while without conducting any operations. The message will disappear shortly. (This operation is no longer valid after the message disappears.) 2 Press the ON/STANDBY button again. The screen turns off, but the internal cooling fan continues to operate for a short while. Then, the projector goes into standby mode. When cooling lamp After cooling complete FLASH A B A During cooling ,the ON/STANDBY indicator flashes. In this state, the power can- not be turned back on. However, there is no problem with unplugging the power cord in this state. B In standby mode Note • The projector consumes about 6W of power in standby. We recommend that you unplug the power cord if you will not be using the projector for an extended period. Precaution • If the power cord is unplugged before cooling is complete, give the lamp time (about 5 minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light. • Right after turning off the power, the unit may become very hot, especially air exhaust and the bottom of the unit. Please handle with care to avoid burn injuries. Operations 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
25
Operations
■
Turning the power off
1
Press the ON/STANDBY button.
A message appears on the screen, confirming that you wish to shut off the power. To
shut off the power, press the ON/STANDBY button again. If you do not wish to shut off
the power, wait for a while without conducting any operations. The message will disap-
pear shortly. (This operation is no longer valid after the message disappears.)
2
Press the ON/STANDBY button again.
The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
A
B
FLASH
A
During cooling ,the ON/STANDBY indicator flashes. In this state, the power can-
not be turned back on.
However, there is no problem with unplugging the power cord in this state.
B
In standby mode
Note
• The projector consumes about 6W of power in standby.We recommend that you unplug
the power cord if you will not be using the projector for an extended period.
Precaution
•
If the power cord is unplugged before cooling is complete, give the lamp time (about 5
minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light.
• Right after turning off the power, the unit may become very hot, especially air exhaust
and the bottom of the unit. Please handle with care to avoid burn injuries.
When cooling lamp
After cooling complete