URC DMS-AV Owners Manual - Page 15

Quick Start Considerations

Page 15 highlights

DMS-AV HOME THEATER AMPLIFIER Quick Start Considerations Your URC receiver is pre-programmed for ease of operation, right out of the box. In general, there is minimal setup required to start using your new DMS-AV Network Home Theater Processor. To quickly setup and begin operating your receiver, follow these steps: 1. Start with all AC power cords unplugged from their designated AC outlet. 2. From each source device, connect the A/V cables which could include composite, component, or HDMI cables. 3. Connect the speaker cables from the receiver's speaker outputs to the appropriate speakers. 4. Connect the appropriate video cables from the receiver's video outputs to the video monitor's input(s). 5. Connect an Ethernet cable from the DMS-AV to local network router. 6. Plug the AC power cords for the DMS-AV and all connected sources into their designated AC outlets. 7. Power On the DMS-AV. Bring the DMS-AV out of "standby" mode, via the front panel "standby" button. 8. Power On all source components. 9. On a computer connected to the same network as the DMS-AV, launch the DMS System Toolbox application. 10. In the unit discovery window, select the Network Scan button. Select the DMS-AV Home Theater Amplifier. 11. In the DMS System Toolbox application, select any of the connected source components. Verify proper operation of the DMS-AV and the source components. Page 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50

Page 16
DMS-AV H
OME
T
HEATER
A
MPLIFIER
Quick Start Considerations
Your URC receiver is pre-programmed for ease of operation, right out of the
box. In general, there is minimal setup required to start using your new
DMS-AV Network Home Theater Processor.
To quickly setup and begin operating your receiver, follow these steps:
1. Start with all AC power cords unplugged from their designated AC outlet.
2. From each source device, connect the A/V cables which could include
composite, component, or HDMI cables.
3. Connect the speaker cables from the receiver’s speaker outputs to the
appropriate speakers.
4. Connect the appropriate video cables from the receiver’s video outputs to
the video monitor’s input(s).
5. Connect an Ethernet cable from the DMS-AV to local network router.
6. Plug the AC power cords for the DMS-AV and all connected sources into
their designated AC outlets.
7. Power On the DMS-AV. Bring the DMS-AV out of “standby” mode, via
the front panel “standby” button.
8. Power On all source components.
9. On a computer connected to the same network as the DMS-AV, launch the
DMS System Toolbox application.
10. In the unit discovery window, select the Network Scan button. Select the
DMS-AV Home Theater Amplifier.
11. In the DMS System Toolbox application, select any of the connected source
components. Verify proper operation of the DMS-AV and the source
components.