URC DMS-AV Owners Manual - Page 19

Video Inputs - Hardware Connections

Get URC DMS-AV PDF manuals and user guides View all URC DMS-AV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

DMS-AV HOME THEATER AMPLIFIER Video Inputs - Hardware Connections Video Input Connection - HDMI The URC surround processor provides 5 HDMI A/V inputs. While HDMI carries both audio and video, URC allows options to process audio and video separately (please see the menu setup for further options). To connect an HDMI video source to the URC DMS AV, connect the HDMI cable to the HDMI output on the source. Then connect the other end of the cable into the corresponding HDMI input on the processor. Shown below is an HDMI output on the source going into IN 9 on the DMS-AV. HDMI connection to HDMI source Video Input Connection - Component Video The DMS-AV provides two sets of component video inputs. Each component input corresponds to a set of stereo analog inputs, labeled with the same input number. Optical digital inputs and coax digital inputs are available to be assigned to either of the component video inputs. For example, component video IN 5 could have it's audio reassigned to optical digital IN A. Shown is a component video source connected to IN 5 on the DMS-AV. Component connection to video source output Video Input Connection - Composite Video The DMS-AV provides four composite video inputs. Each composite input corresponds to a set of stereo analog inputs, labeled with the same input number. These inputs may be used to up-convert a composite video signal to the HDMI output. Connect the composite video output on the source using an RCA cable to the yellow colored input on the DMS-AV. Shown below is a composite video source with an RCA connection going into the yellow RCA input of IN 1. Composite connection to video source Page 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
Page 20
DMS-AV H
OME
T
HEATER
A
MPLIFIER
Video Inputs - Hardware Connections
Video Input Connection – HDMI
The URC surround processor provides 5 HDMI A/V inputs. While HDMI
carries both audio and video, URC allows options to process audio and
video separately (please see the menu setup for further options). To connect
an HDMI video source to the URC DMS AV, connect the HDMI cable to
the HDMI output on the source. Then connect the other end of the cable
into the corresponding HDMI input on the processor. Shown below is an
HDMI output on the source going into
IN 9
on the DMS-AV.
Video Input Connection - Component Video
The DMS-AV provides two sets of
component video inputs. Each
component input corresponds to a
set of stereo analog inputs, labeled
with the same input number.
Optical digital inputs and coax
digital inputs are available to be
assigned
to either of the
component video inputs. For
example, component video
IN 5
could have it’s audio reassigned
to optical digital
IN A
. Shown is a
component video source
connected to
IN 5
on the DMS-AV.
Video Input Connection - Composite Video
The DMS-AV provides four composite video inputs. Each composite input
corresponds to a set of stereo analog inputs, labeled with the same input
number.
These inputs may be used to up-convert a composite video signal to
the HDMI output. Connect the composite video output on the source using an
RCA cable to the yellow colored input on the DMS-AV. Shown below is a
composite video source with an RCA
connection going into the yellow RCA
input of
IN 1
.
HDMI connection to HDMI source
Component connection to video source output
Composite connection to video source