Uniden BC780XLT English Owners Manual - Page 17

Applying Power for Vehicle Installation - power supply

Get Uniden BC780XLT PDF manuals and user guides View all Uniden BC780XLT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Applying Power for Vehicle Installation You can power your scanner using either the supplied DC power cord or your vehicle's cigarette lighter socket using DC cigarette lighter power cord. Caution: You must use a power source that supplies 13.8 V DC and delivers at least 700 mA. Your standard 12 V car battery should be sufficient. The cord connector's center tip must be set to positive and its plug must fit the scanner's DC 13.8 V jack. The supplied DC power cord meets these specifications. Using a power cord that does not meet these specifications could damage the scanner or the adapter. • Always connect the adapter or DC power cord to the scanner before you connect it to the power source. When you finish, disconnect the adapter or DC power cord from the power source before you disconnect it from the scanner. • For added safety and to protect your scanner, disconnect the cable from your vehicle battery's negative (-) terminal before you begin. Follow these steps to connect the supplied DC power cord. 1. Connect the power cord's black wire to a chassis ground, such as a metal screw attached to a metal part of the vehicle's frame. Be sure that the screw is not insulated from the frame by a plastic part. 2. Connect the power cord's red wire (with in-line fuse) to a source of voltage that turns on and off with the ignition switch, such as a spare accessory terminal in your vehicle's fuse box. 3. Insert the power cord's barrel plug into the DC 13.8 V jack on the back of the scanner. 4. Reconnect the cable to the vehicle battery's negative (-) terminal. To power the scanner from a vehicle's 12 V power source (such as a cigarette-lighter socket), you need a cigarette-lighter adapter. To connect an optional DC cigarette-lighter power cable, insert its barrel plug into the DC 13.8 V jack on the back of the scanner, then plug the power cable into your vehicle's cigarette lighter socket. Note: If you use a cigarette-lighter power cable and your vehicle's engine is running, you might hear electrical noise from the engine while scanning. This is normal. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
9
Applying Power for Vehicle Installation
You can power your scanner using either the supplied DC power cord or your vehicle
’
s
cigarette lighter socket using DC cigarette lighter power cord.
Caution
:
You must use a power source that supplies 13.8 V DC and delivers at least
700 mA. Your standard 12 V car battery should be sufficient. The cord connector
’
s
center tip must be set to positive and its plug must fit the scanner
’
s
DC 13.8 V
jack. The supplied DC power cord meets these specifications. Using a power cord
that does not meet these specifications could damage the scanner or the adapter.
•
Always connect the adapter or DC power cord to the scanner before you connect it to the
power source. When you finish, disconnect the adapter or DC power cord from the power
source before you disconnect it from the scanner.
•
For added safety and to protect your scanner,
disconnect the cable from your vehicle battery
’
s
negative (-) terminal before you begin.
Follow these steps to connect the supplied DC power cord.
1.
Connect the power cord
’
s black wire to a chassis ground, such as a metal screw
attached to a metal part of the vehicle
’
s frame. Be sure that the screw is not insulated
from the frame by a plastic part.
2.
Connect the power cord
’
s red wire (with in-line fuse)
to a source of voltage that turns on and off with the
ignition switch, such as a spare accessory terminal in
your vehicle
’
s fuse box.
3.
Insert the power cord
’
s barrel plug into the
DC 13.8 V
jack on the back of the scanner.
4.
Reconnect the cable to the vehicle battery
’
s
negative (-) terminal.
To power the scanner from a vehicle
’
s 12 V power source (such as a cigarette-lighter
socket), you need a cigarette-lighter adapter.
To connect an optional DC cigarette-lighter power cable, insert its barrel plug into the
DC 13.8 V
jack on the back of the scanner, then plug the power cable into your vehicle
’
s
cigarette lighter socket.
Note
:
If you use a cigarette-lighter power cable and your vehicle
’
s engine is running, you
might hear electrical noise from the engine while scanning. This is normal.