Uniden BC780XLT English Owners Manual - Page 46

Selecting Trunking Programming Menu Mode, Selecting Trunking System Type

Get Uniden BC780XLT PDF manuals and user guides View all Uniden BC780XLT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Important! 7. Press TRUNK for 2 seconds. A tone sounds, and E, M, or L icon appears on the display according to the system selected. Note: • To clear a mistake while entering the frequency, press (decimal key) repeatedly until the display is cleared. • If you enter a frequency which is out of the system's trunking range, a distinctive beep sounds and ERROR appears on the display. Selecting Trunking Programming Menu Mode To change the system type which your scanner monitors, you must be in the Trunking Programming menu mode. To select this mode, follow these steps: 1. Press MENU. 2. Press or to select TRUNK DATA and then press E. 3. Select the bank you want to program using , or VFO and then press E. Remember! You can also use the VFO control for scrolling. Also instead of pressing E, you can press the VFO/SELECT control or press the SELECT/MUTE key. Selecting Trunking System Type 1. Select TRUNK TYPE using , or VFO and then press E, SELECT or VFO. 2. Select the system type you want to program using , or VFO and then press E, SELECT or VFO. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
38
☞
Important!
7.
Press
TRUNK
for 2 seconds.
A tone sounds, and
E
,
M
, or L icon appears on the display according to the system
selected.
Note
:
•
To clear a mistake while entering the frequency,
press
(decimal key) repeatedly until the
display is cleared.
•
If you enter a frequency which is out of the
system
’
s trunking range, a distinctive beep
sounds and ERROR appears on the display.
Selecting Trunking Programming Menu Mode
To change the system type which your scanner monitors, you must be in the Trunking
Programming menu mode.
To select this mode, follow these steps:
1.
Press
MENU
.
2.
Press
▲
or
▼
to select
TRUNK DATA
and then
press
E
.
3.
Select the bank you want to program using
▲
,
▼
or
VFO
and then press
E
.
☞
Remember!
You can also use the
VFO
control for scrolling. Also instead of pressing
E
, you can press the
VFO/SELECT
control or press the
SELECT/MUTE
key.
Selecting Trunking System Type
1.
Select
TRUNK TYPE
using
▲
,
▼
or
VFO
and then
press
E
,
SELECT
or
VFO
.
2.
Select the system type you want to program
using
▲
,
▼
or
VFO
and then press
E
,
SELECT
or
VFO
.