Uniden BCD996T English Owners Manual - Page 80

Setting Site Hold Time, Editing the Band Plan, Edit Site, Set Lockout, Unlocked, Temporary L/O

Get Uniden BCD996T PDF manuals and user guides
UPC - 050633650486
View all Uniden BCD996T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Edit Site F Select a site F Set Lockout F Select from the following choices then press F Unlocked - the system is scanned when its quick key is enabled. Temporary L/O - the system is locked for this session. Lockout - the system is not scanned. Setting Site Hold Time [MENU] Program System F Select a trunked system F Edit Site F Select a site F Set Hold Time F MESL This setting controls how many seconds the scanner looks at a site before moving to the next unlocked site or system. Using the number keypad, enter a value from 0-255, then press F to save the setting. Notes: • If the scanner cannot detect a control channel on an EDACS or Motorola system, it immediately moves to the next site or system. The scanner always scans LTR or SCAT systems for at least 1 second to check for current activity. • If you select 0 and the control channel is received, the scanner stays on the system for a minimal time (only long enough to check current system activity). • The default setting is 2 seconds for each system. • The scanner moves to the next system after the hold time expires, any current transmission ends, and the channel delay time expires. Editing the Band Plan M (VHF and UHF only) In order for the scanner to scan Motorola VHF and UHF sites, you must enter parameters that allow the scanner to determine the frequencies in use by the system. This information is normally available at the same source where the other system information is found. [MENU] Program System F Select a trunked system F Edit Site F 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
80
4
Edit Site
J
F
4
Select a site
J
F
4
Set Lockout
J
F
4
Select from the following choices
then press
F
Unlocked
— the system is scanned when its quick key is enabled.
Temporary L/O
— the system is locked for this session.
Lockout
— the system is not scanned.
[MENU]
J
Program System
J
F
4
Select a trunked system
J
F
4
Edit Site
J
F
4
Select a site
J
F
4
Set Hold Time
J
F
This setting controls how many seconds the scanner looks at a site before moving
to the next unlocked site or system. Using the number keypad, enter a value from
0-255, then press
F
to save the setting.
Notes:
•
If the scanner cannot detect a control channel on an EDACS or Motorola
system, it immediately moves to the next site or system. The scanner always
scans LTR or SCAT systems for at least 1 second to check for current activity.
•
If you select 0 and the control channel is received, the scanner stays on the
system for a minimal time (only long enough to check current system activity).
•
The default setting is 2 seconds for each system.
•
The scanner moves to the next system after the hold time expires, any current
transmission ends, and the channel delay time expires.
In order for the scanner to scan Motorola VHF and UHF sites, you must enter
parameters that allow the scanner to determine the frequencies in use by the
system. This information is normally available at the same source where the other
system information is found.
[MENU]
J
Program System
J
F
4
Select a trunked system
J
F
4
Edit Site
J
F
Setting Site Hold Time
MESL
Editing the Band Plan
M (VHF and UHF only)