Viking RDMOS201SS 30 inch W. Built-In Trim Kit - Installation Instructions - Page 12
Information générale
View all Viking RDMOS201SS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
Information générale Pièces comprises dans le kit 1) Frame Assembly: QTY 1 Numéro Nom de pièce 1 Cadre de porte 2 Conduit inférieur 3 Bride de fixation Qté 1 1 2 Découpe de l'armoire ou 2) Bottom Duct Assembly: QTY 1 du mur Dimensions de la Fixation Fixation en découpe encastrée surface Hauteur A Minimum 17-5/16 po 16-9/16 po (439,8 mm) (420,7 mm) 4 Vis A : longueur 1-3/16 po (30,2 mm) 2 Maximum N/A 16-13/16po 5 Vis B : longueur 1 3/4 po (44,5 mm) 4 (427 mm) 6 Décorations latérales (pour fixation en surface uniquement) 2 Largeur B Minimum 29-5/8 po 27-3/4 po (752,5 mm) (704,9 mm) 7 Gabarit de fixation en surface 1 Maximum N/A 28 po (711,2 mm) 8 1) FraGmae bAsasreimt bdlye: QfiTxYa1tion encas3tr) éMeouting Bracket: Q2)1TBYo2ttom Duct Assembly: QTY 1 Profondeur C 4) SIDE DECORATION: QTY 2 Minim(SuUmRFAC2E0MpOoUNTING ONL2Y0) po (503mm) (503mm) 2) Bottom Duct Assembly: QTY 1 1 3 1 4 po (102 mm) 6 po (15,2 mm) Y 1 2) Bottom Duct Assembly: QTY 1 figure Y 2 2 3) Mouting Bracket: QTY 2 4) SIDE DECORATION: QTY 2 (SURFACE MOUNTING ONLY) 6 4 4) SIDE DECORATION: QTY 2 (SURFACE MOUNTING ONLY) 4 po (102 mm) 5 Emplacement de la prise électrique 4) SIDE DECOR7ATION: QTY 2 (SURFACE MOUNTING ONLY) Maximum Cutout Opening Width 28" (711.2 mm) Minimum Cutout Opening Width 27-3/4" (704.9 mm) Minimum Cutout Opening Height 16-9/16" (420.7 mm) Maximum Cutout Opening Height 16-13/16" (427 mm) Distance between holes A9.1" (231.2 mm) BUILT-IN TRIM KIT SURFACE MOUNTING TEMPLATE FOR DESIGNER SERIES MICROWAVE OVEN Center Line 1. Align the Surface Mounting Template center line with the center of the cabinet. Align the Floor Line with the bottom of the cabinet at the desired height. Tape it into place. 2. Predrill 4 holes marked A with a drill bit. 3. Cut the cabinet opening between the minimum and maximum cutout opening lines. Be careful to cut precisely along the Floor Line of the cutout. 4. Remove template from the cabinet. 3-15/16" (100 mm) 14-1/4" (361.95 mm) 1/4" (6.2 mm) 14" (355.6 mm) Floor Line of Cutout Opening 8 Cutout Opening Width 29-5/8" (752.5 mm) CABINET CUTOUT LINE CABINET CUTOUT LINE CABINET CUTOUT LINE SIDE SPACER TEMPLATE - L Align Side Spacer-L to this line 13-1/2" min. height Edges to align Side Spacer Templates (R and L) 13/16" Min. 15/16 Max. FIGURE 1 Side Spacer (2 required) Must protrude from edge of cabinet cutout towards center as shown. 24" min. width 27-7/8" max. width FIGURE 2 Bottom Spacer (1 required) ¹₄" plywood Side Spacer - L Side Spacer - R Bottom Spacer centered with cabinet cutout FIGURE 3 1-9/16" (39.7 mm) Bottom and Side Spacer (R and L) Offset 1/4" (6.35 mm) 14" (355.9 mm) 14-13/16" (376.2 mm) FLOOR LINE OF CUTOUT OPENING CENTER LINE BUILT-IN TRIM KIT FLUSH MOUNTING TEMPLATE FOR DESIGNER SERIES MICROWAVE OVEN 1. Align the Flush Mounting Template center line with the center of the cabinet. Align the Floor Line with the bottom of the cabinet at the desired height. Tape it in place. 2. Cut the cabinet opening along the three Cabinet Cutout Lines and the Floor Line. 3. Install two Side Spacers (see FIGURE 1) and one Bottom Spacer (see FIGURE 2) as specified in FIGURE 3. Be sure to offset all three spacers by 1 from the front surface of the cabinet. 4. Cut out the Side Spacer Templates (R and L) and align the indicated edge to the corresponding Side Spacer (see FIGURE 3). Be careful to align the Floor Line to the bottom edges of the Side Spacers. 5. Predrill two holes indicated "A" in Side Spacer - R with a drill bit. 6. Predrill two holes indicated "B" in Side Spacer - L with a drill bit. 7. Remove template from the cabinet. 4-3/16" (106.4 mm) 1/4" (6.35 mm) TINSLB009MRR0 Distance between holes A9.1" (231.2 mm) Cutout Opening Height 17-5/16" (439.8 mm) Align Side Spacer-R to this line SIDE SPACER TEMPLATE - R TINSLB008MRR0 1/4" (6.2 mm) MISE EN GARDE La prise NE doit PAS se trouver dans l'aire ombrée comme indiqué à l'Illustration 1. NOTES : • Si la profondeur (C) dépasse 53,3 cm (21 po), l'emplacement de la prise peut être situé n'importe où sur le mur arrière. • Le plancher de l'ouverture doit être en contreplaqué assez fort pour supporter le poids du four et sa propre charge (environ 45,5 kg [100 lb]). Il doit être à un niveau convenable pour l'utilisation du four. Veiller à vérifier le code local du bâtiment, car il pourrait exiger que l'ouverture soit fermée par une cloison latérale, arrière et un plafond. Le four n'a pas besoin d'être enclos pour fonctionner. F 12