Viking RDMOS201SS 30 inch W. Built-In Trim Kit - Installation Instructions - Page 20

Información general Par tes incluidas en el juego 1) Frame Assembly: QTY 1 Aber tura del gabinete 2) Bottom Duct Assembly: QTY 1 o pared Artículo Nombre de la parte 1 Conjunto del marco 2 Conjunto del ducto inferior 3 Soporte de montaje 4 Tornillo A :1-3/16" de largo CANT. 1 1 2 2 Dimensiones de recorte Altura A Mínimo Máximo Brindas Montaje 17-5/16" (439.8mm) N/A Superficie Montaje 16-9/16" (420.7mm) 16-13/16" (427mm) 5 Tornillo B: 1-3/4" de largo 4 Ancho B 6 Decoración lateral (Sólo superficie de montaje) 2 7 Plantilla para montaje en superficie 1 8 1) FraPmleanAstsiellmabplya: QraTYm1 ontaje al r3a) Ms outing Bracket: Q21)TBYo2ttom DucPtrAosfsuemndbliyd: QadTYC1 Mínimo 29-5/8" 27-3/4" (752.5mm) (704.9mm) Máximo N/A 28" (711.2mm) Mínimo 20" 20" 4()SSUIRDFEADCEECMO(O5R0UANT3ITOmINNmG: Q)OTNYL2Y) (503mm) 2) Bottom Duct Assembly: QTY 1 1 3 1 4"(10.2 cm) 6"(15.2 cm) figura 1 2) Bottom Duct Assembly: QTY 1 2 3) Mouting Bracket: QTY 2 4) SIDE DECORATION: QTY 2 (SURFACE MOUNTING ONLY) 6 4 4) SIDE DECORATION: QTY 2 (SURFACE MOUNTING ONLY) 4"(10.2 cm) Ubicación del 5 tomacorriente eléctrico 2 4) SIDE DECOR7 ATION: QTY 2 (SURFACE MOUNTING ONLY) PRECAUCIÓN Maximum Cutout Opening Width 28" (711.2 mm) Minimum Cutout Opening Width 27-3/4" (704.9 mm) El tomacorriente NO debe estar en el área sombreada como se indica en la figura 1. Distance between holes A9.1" (231.2 mm) BUILT-IN TRIM KIT SURFACE MOUNTING TEMPLATE FOR DESIGNER SERIES MICROWAVE OVEN Center Line 1. Align the Surface Mounting Template center line with the center of the cabinet. Align the Floor Line with the bottom of the cabinet at the desired height. Tape it into place. 2. Predrill 4 holes marked A with a drill bit. 3. Cut the cabinet opening between the minimum and maximum cutout opening lines. Be careful to cut precisely along the Floor Line of the cutout. 4. Remove template from the cabinet. NOTAS: Minimum Cutout Opening Height 16-9/16" (420.7 mm) Maximum Cutout Opening Height 16-13/16" (427 mm) 14-1/4" (361.95 mm) 1/4" (6.2 mm) 14" (355.6 mm) Floor Line of Cutout Opening 8 Cutout Opening Width 29-5/8" (752.5 mm) CABINET CUTOUT LINE CABINET CUTOUT LINE CABINET CUTOUT LINE SIDE SPACER TEMPLATE - L Align Side Spacer-L to this line 13-1/2" min. height Edges to align Side Spacer Templates (R and L) 13/16" Min. 15/16 Max. FIGURE 1 Side Spacer (2 required) Must protrude from edge of cabinet cutout towards center as shown. 24" min. width 27-7/8" max. width FIGURE 2 Bottom Spacer (1 required) ¹₄" plywood Side Spacer - L Side Spacer - R Bottom Spacer centered with cabinet cutout FIGURE 3 1-9/16" (39.7 mm) Bottom and Side Spacer (R and L) Offset 1/4" (6.35 mm) 14" (355.9 mm) 14-13/16" (376.2 mm) FLOOR LINE OF CUTOUT OPENING CENTER LINE BUILT-IN TRIM KIT FLUSH MOUNTING TEMPLATE FOR DESIGNER SERIES MICROWAVE OVEN 1. Align the Flush Mounting Template center line with the center of the cabinet. Align the Floor Line with the bottom of the cabinet at the desired height. Tape it in place. 2. Cut the cabinet opening along the three Cabinet Cutout Lines and the Floor Line. 3. Install two Side Spacers (see FIGURE 1) and one Bottom Spacer (see FIGURE 2) as specified in FIGURE 3. Be sure to offset all three spacers by 1 from the front surface of the cabinet. 4. Cut out the Side Spacer Templates (R and L) and align the indicated edge to the corresponding Side Spacer (see FIGURE 3). Be careful to align the Floor Line to the bottom edges of the Side Spacers. 5. Predrill two holes indicated "A" in Side Spacer - R with a drill bit. 6. Predrill two holes indicated "B" in Side Spacer - L with a drill bit. 7. Remove template from the cabinet. 4-3/16" (106.4 mm) 1/4" (6.35 mm) TINSLB009MRR0 Distance between holes A9.1" (231.2 mm) Cutout Opening Height 17-5/16" (439.8 mm) Align Side Spacer-R to this line SIDE SPACER TEMPLATE - R TINSLB008MRR0 1/4" (6.2 mm) 3-15/16" (100 mm) • Si la dimensión de profundidad (C) es mayor a 21" (53.3 cm), la ubicación del tomacorriente puede estar en cualquier área de la pared posterior. • El piso de la abertura debe estar construido de madera laminada lo suficientemente resistente para soportar el peso del horno y la capacidad de carga (aproximadamente 100 libras). El piso debe estar nivelado para una correcta operación del horno. Asegúrese de verificar el código de construcción local ya que puede requerir cercar la abertura con tabiques laterales, superior y posterior. El funcionamiento apropiado del horno no requiere del cercado. S 20