Viking RDSCE2305BSS Installation Instructions - Page 7

General Information, Installation, Backguard Installation, Door Removal

Get Viking RDSCE2305BSS PDF manuals and user guides View all Viking RDSCE2305BSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

General Information READ AND FOLLOW ALL WARNING AND CAUTION INFORMATION WHEN INSTALLING THIS APPLIANCE. • All openings in the wall behind the appliance and in the floor under the appliance must be sealed. • DO NOT obstruct the flow of combustion and ventilation air. CAUTION Avoid any damage to oven vents. The vents need to be unobstructed and open to provide proper airflow for optimal oven performance. CAUTION The cooling fan should be operating when the unit is in operation. If you notice the cooling fan is not operating or you observe unusual or excessive noise coming from the cooling fan, contact a Viking Authorized Service Center before continuing operation. Failure to do so can result in damage to the oven or surrounding cabinets. Moving, Handling, and Unpacking Remove and discard all packing materials, including cardboard and tape on the outside and inside of the range. Range - Do not discard the anti-tip metal brackets (2) supplied with the range. These are the anti-tip devices and one must be installed with the unit. Refer to "Anti-tip Device Installation" section. Some stainless steel parts may have a plastic protective wrap which must be peeled off. The interior should be washed thoroughly with hot, soapy water to remove film residues and any dust or debris before being used, then rinsed and wiped dry. Solutions stronger than soap and water are rarely needed. 12 Installation CAUTION To avoid risk of personal injury or product damages, DO NOT use the handle or oven door to lift the oven. Remove door before installation to ensure that it is not used to lift the unit. DO NOT lift or carry the door by the handle. Removing the door must be done by your dealer, or a qualified licensed plumber. Door Removal 1 Backguard Installation 1 1 x4 2 Attach backguard to range with screws provided. 2 Open door completely. Place pins, supplied with unit, in pin hole. For personal safety, ONLY use pins supplied with the unit. 3 Remove hinge trim screws. Take off hinge trim. Identify right and left hinge for future re-installation. 4 Close until pins stop door. 13 Lift door up and out.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
13
12
General Information
READ AND FOLLOW ALL WARNING
AND CAUTION INFORMATION WHEN
INSTALLING THIS APPLIANCE.
• All openings in the wall behind the
appliance and in the floor under the
appliance must be sealed.
•
DO NOT
obstruct the flow of combustion
and ventilation air.
Moving, Handling, and Unpacking
Remove and discard all packing materials,
including cardboard and tape on the outside
and inside of the range.
Range –
Do not discard the
anti-tip metal brackets (2)
supplied with the range.
These are the anti-tip devices
and one must be installed
with the unit.
Refer to
“Anti-tip Device Installation”
section.
Some stainless steel parts
may have a plastic protective
wrap which must be peeled
off. The interior should be washed
thoroughly with hot, soapy water to remove
film residues and any dust or debris before
being used, then rinsed and wiped dry.
Solutions stronger than soap and water are
rarely needed.
CAUTION
Avoid any damage to oven vents. The vents
need to be unobstructed and open to provide
proper airflow for optimal oven performance.
CAUTION
The cooling fan should be operating when
the unit is in operation. If you notice the
cooling fan is not operating or you observe
unusual or excessive noise coming from the
cooling fan, contact a Viking Authorized
Service Center before continuing operation.
Failure to do so can result in damage to the
oven or surrounding cabinets.
CAUTION
To avoid risk of personal injury or product
damages,
DO NOT
use the handle or
oven door to lift the oven. Remove door
before installation to ensure that it is not
used to lift the unit.
DO NOT
lift or carry
the door by the handle.
Removing the door must be done by your
dealer, or a qualified licensed plumber
.
Door Removal
1
Open door completely. Place pins,
supplied with unit, in pin hole. For personal safety,
ONLY use pins supplied with the unit.
Backguard Installation
1
2
1
x4
Attach backguard to range with screws provided.
2
Remove hinge trim screws. Take off hinge trim. Identify
right and left hinge for future re-installation.
3
Close until pins stop door.
4
Lift door up and out.
Installation