Vtech DS6151 User Manual (DS6151 User Manual) - Page 84

The messages on the answering system are very difficult to hear.

Get Vtech DS6151 - 6.0 Expandable Cordless Phone PDF manuals and user guides
UPC - 735078016584
View all Vtech DS6151 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

Appendix Troubleshooting The messages on the answering system are very difficult to hear. • Press /VOL o��n��th�e��h�a��n�d�s�e�t��o�r�t�e�le��p�h�o�n�e��b��a�s�e��to��i�n�c�r�e�a�s�e��t�h�e��s�p�e�a�k�e��r�v�o�l�u�m��e�. The messages on the answering system are incomplete. • If a caller leaves a very long message, part of it may be lost when the answering system disconnects the call after four minutes. • If the memory on the answering system becomes full during a message, the answering system stops recording and disconnects the call. • If the caller's voice is very soft, the answering system may stop recording and disconnect the call. The answering system does not respond to remote commands. • Make sure your remote access code is correct (page 27). • Make sure you are calling from a touch-tone telephone. When dialing a number, there should be tones. If there are clicks, then it is not a touch-tone telephone and cannot activate the answering system. • The answering system may not detect the remote access code when your announcement is playing. Wait until the announcement is over before entering the code. • There may be interference on the telephone line you are using. Press the dial pad keys firmly when dialing. Common cures for electronic equipment. • If the telephone is not responding normally, put the cordless handset in the telephone base. If it does not respond, try the following (in the order listed): • Disconnect the power to the telephone base. • Disconnect the battery on the cordless handset. • Wait a few minutes before connecting power to the telephone base. • Reinstall the battery and place the cordless handset in the telephone base . • Wait for the cordless handset to synchronize with the telephone base. Allow up to one minute for this to take place. 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
80
Appendix
Troubleshooting
The messages on the answering system are very difficult to hear.
Press
/VOL
on the handset or telephone base to increase the speaker volume.
on the handset or telephone base to increase the speaker volume.
The messages on the answering system are incomplete.
If a caller leaves a very long message, part of it may be lost when the answering
system disconnects the call after four minutes.
If the memory on the answering system becomes full during a message, the
answering system stops recording and disconnects the call.
If the caller’s voice is very soft, the answering system may stop recording and
disconnect the call.
The answering system does not respond to remote commands.
Make sure your remote access code is correct (page 27).
Make sure you are calling from a touch-tone telephone. When dialing a number,
there should be tones. If there are clicks, then it is not a touch-tone telephone and
cannot activate the answering system.
The answering system may not detect the remote access code when your
announcement is playing. Wait until the announcement is over before entering
the code.
There may be interference on the telephone line you are using. Press the dial pad
keys firmly when dialing.
Common cures for electronic equipment.
If the telephone is not responding normally, put the cordless handset in the
telephone base. If it does not respond, try the following (in the order listed):
Disconnect the power to the telephone base.
Disconnect the battery on the cordless handset.
Wait a few minutes before connecting power to the telephone base.
Reinstall the battery and place the cordless handset in the telephone base .
Wait for the cordless handset to synchronize with the telephone base. Allow up to
one minute for this to take place.
•
•
•
•
•
•
•
•
•
•
•
•
•
•