Weider 9645 Instruction Manual - Page 12

CABLE ASSEMBLY CABLE ASSEMBLY 20. Wrap the High Cable (58) around a "V"-Pulley 20 (50). Attach the "V"-Pulley and a Long Cable Trap (31) to the indicated bracket on the Front Upright (42) with a 3/8" x 2 1/2" Bolt (86) and a 3/8" Nylon Locknut (21). Be sure that the Long Cable Trap is positioned to hold the Cable in place. 21. Route the High Cable (58) around the "V"Pulley (50) on the Left Arm (47). Be sure that 21 the Cable is in the groove of the Pulley and that the Long Cable Trap (31) is posi- tioned to hold the Cable in place. Tighten the 3/8" x 2 1/2" Bolt (86) and the 3/8" Nylon Locknut (not shown). 86 31 58 50 Bracket 42 21 86 31 50 58 47 22. Route the High Cable (58) around the "V"- 22 Pulley (50) on the Right Arm (48). Be sure that the Cable is in the groove of the "V"- Pulley and that the Long Cable Trap (31) is turned to hold the Cable in place. Tighten the 3/8" x 2 1/2" Bolt (86) and the 3/8" Nylon Locknut (not shown). 31 86 50 58 48 23. Attach the Pulley Bracket (20) to the Top 23 Frame (55) with the 5/16" x 5" Bolt (68) and a 68 5/16" Nylon Locknut (3). Do not overtighten the Nylon Locknut; the Pulley Bracket must be able to move freely. See the inset drawing. Route the High Cable 55 66 (58) around the 3 1/2" Pulley (15) attached to the Pulley Bracket (20). Tighten the 3/8" x 2" 20 12 Bolt (12) and a 3/8" Nylon Locknut (not shown). Be sure that the Cable is in the groove of the Pulley and that the Cable 3 15 58 Trap (66) is turned to hold the Cable in place. 12 36. Slide a 5/16" Flat Washer (8) onto a 5/16" x 2 3/4" Bolt (11). Insert the Bolt through the indicated hole in the Pivot Arm (101). The Bolt must be inserted from the side shown. Fully tighten a 5/16" Nylon Jam Nut (93) onto the Bolt. Wrap the Military Press Cable (72) around a 3 1/2" Pulley (15). Attach the Pulley and a Cable Trap (66) to the Pivot Arm (101) with the 3/8" x 3 3/4" Bolt (88), a 3/8" Flat Washer (9), and a 3/8" Nylon Locknut (21). Be sure that the Pulley is on the side shown and that the Cable Trap is positioned to hold the Cable in place. 36 21 93 9 101 72 15 8 11 66 88 37. See inset drawing A. Attach a 3 1/2" Pulley (15) and a Cable Trap (66) to the upper hole in a Long "U"-Bracket (57) with a 3/8" x 2" Bolt (12) and a 3/8" Nylon Locknut (21). Be sure that the Cable Trap is inside the Long "U"-Bracket. (Note: This may come preassembled.) Route the Military Press Cable (72) through the Long "U"-Bracket (57) and the 3 1/2" Pulley (15). Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly. See inset drawing B. Slide the end of the Military Press Cable (72) onto the end of the 5/16" x 2 3/4 Bolt (11). Thread another 5/16" Nylon Jam Nut (93) onto the Bolt. Do not fully tighten the second Jam Nut. There must be room between the two Jam Nuts for the end of the Cable to pivot. 37 15 57 72 21 57 93 72 11 15 A 66 12 B 17