Weider Club 4870 English Manual - Page 19

Attach the Pulley, a Cable Trap 48, and a Guard

Get Weider Club 4870 PDF manuals and user guides View all Weider Club 4870 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

38. Wrap the Low Cable (70) under a Pulley (43). 38 Attach the Pulley, an M10 Washer (108), and two Half Guards (46) to the Right Base (1) with an M10 x 45mm Bolt (95) and an M10 Nylon Locknut (84). Make sure the Half Guards are oriented as shown. 70 84 46 43 108 1 39. Route the Low Cable (70) over a Pulley (43) and 39 through the Center Upright (9). Attach the Pulley inside the Center Upright with an M10 x 65mm Bolt (87), two M10 Washers (108), two 1/2" Bushings (68), and an M10 Nylon Locknut (84). 84 108 68 43 70 46 95 108 68 87 9 40. Wrap the Low Cable (70) under a Pulley (43). 40 Attach the Pulley, a Cable Trap (48), and a Guard (45) to the Small Pulley Plate (50) with an M10 x 50mm Bolt (105) and an M10 Nylon Locknut (84). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 41. Wrap the Low Cable (70) over a Pulley (43). 41 Attach the Pulley to the Left Top Frame (4) with an M10 x 45mm Bolt (95) and an M10 Nylon Locknut (84). 70 105 50 84 48 45 43 4 84 43 70 95 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
19
38. Wrap the Low Cable (70) under a Pulley (43).
Attach the Pulley, an M10 Washer (108), and two
Half Guards (46) to the Right Base (1) with an
M10 x 45mm Bolt (95) and an M10 Nylon Locknut
(84).
Make sure the Half Guards are oriented
as shown.
39. Route the Low Cable (70) over a Pulley (43) and
through the Center Upright (9). Attach the Pulley
inside the Center Upright with an M10 x 65mm
Bolt (87), two M10 Washers (108), two 1/2”
Bushings (68), and an M10 Nylon Locknut (84).
40. Wrap the Low Cable (70) under a Pulley (43).
Attach the Pulley, a Cable Trap (48), and a Guard
(45) to the Small Pulley Plate (50) with an M10 x
50mm Bolt (105) and an M10 Nylon Locknut (84).
Make sure that the Cable Trap is oriented to
hold the Cable in the groove of the Pulley.
38
1
84
46
43
108
70
95
46
40
41
84
39
105
50
43
48
45
70
84
84
43
4
95
70
41. Wrap the Low Cable (70) over a Pulley (43).
Attach the Pulley to the Left Top Frame (4) with
an M10 x 45mm Bolt (95) and an M10 Nylon
Locknut (84).
68
68
87
9
43
70
108
108