Weider Club 4870 English Manual - Page 8

Frame Assembly

Get Weider Club 4870 PDF manuals and user guides View all Weider Club 4870 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Frame Assembly 1. Before beginning assembly, make sure you understand the information in the box on the previous page. For help identifying small parts, use the PART IDENTIFICATION CHART on pages 5 and 6. Insert four M10 x 80mm Carriage Bolts (88) up through the Right Base (1). Place a piece of tape over the Bolt heads to hold the Carriage Bolts in place. See the inset drawing. Insert two M10 x 80mm Carriage Bolts (88) up through the Left Base (2). Place a piece of tape over the Bolt heads to hold the Carriage Bolts in place. 2. Attach the Center Base (5) to the Right and Left Bases (1, 2) with four M10 x 70mm Bolts (57), four M10 Washers (108), and two M10 Nylon Locknuts (84). Do not tighten the Bolts yet. 1 1 88 2 88 2 57 108 1 88 84 84 5 57 108 2 3. Orient the Center Upright (9) so the 2" Square 3 Inner Cap (51) is in the position shown. Attach 51 the Center Upright to the Right and Left Bases (1, 2) with four M10 x 70mm Bolts (57), four M10 Washers (108), and two M10 Nylon Locknuts (84). Do not tighten the Bolts yet. 9 57 108 84 1 108 57 108 84 2 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
8
1.
Insert four M10 x 80mm Carriage Bolts (88) up
through the Right Base (1). Place a piece of tape
over the Bolt heads to hold the Carriage Bolts in
place.
See the inset drawing.
Insert two M10 x 80mm
Carriage Bolts (88) up through the Left Base (2).
Place a piece of tape over the Bolt heads to hold
the Carriage Bolts in place.
2.
Attach the Center Base (5) to the Right and Left
Bases (1, 2) with four M10 x 70mm Bolts (57),
four M10 Washers (108), and two M10 Nylon
Locknuts (84).
Do not tighten the Bolts yet.
1
88
88
1
2
108
108
5
1
2
57
57
84
84
9
2
108
108
84
84
108
57
57
3
1
51
Before beginning assembly, make sure you
understand the information in the box on
the previous page. For help identifying
small parts, use the PART IDENTIFICATION
CHART on pages 5 and 6.
Frame Assembly
88
2
3.
Orient the Center Upright (9) so the 2" Square
Inner Cap (51) is in the position shown. Attach
the Center Upright to the Right and Left Bases (1,
2) with four M10 x 70mm Bolts (57), four M10
Washers (108), and two M10 Nylon Locknuts
(84).
Do not tighten the Bolts yet.