Weider Club 4870 English Manual - Page 21

Left Seat Upright 14 with an M10 x 120mm Bolt

Get Weider Club 4870 PDF manuals and user guides View all Weider Club 4870 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

47. Wrap the Press Cable (72) under a Pulley (43). 47 Attach the Pulley, a Cable Trap (48), an M10 Washer (108), and two Half Guards (46) to the Left Seat Upright (14) with an M10 x 120mm Bolt (97) and an M10 Nylon Locknut (84). Make sure 14 that the Cable Trap is oriented to hold the Cable in the groove of the Pulley. Make sure the Half Guards are oriented as shown. 43 48 46 108 72 97 46 84 48. Note: This step is shown from the opposite 48 side of the Press Frame (13). Wrap the Press Cable (72) under a Pulley (43). Attach the Pulley, a Cable Trap (48), an M10 Washer (108), and two Half Guards (46) to the Press Frame (13) with an M10 x 45mm Bolt (95) and an M10 Nylon Locknut (84). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley. Make sure the Half Guards are oriented as shown. 49. Wrap the Press Cable (72) under a Pulley (43). Attach the Pulley, a Cable Trap (48), an M10 49 Washer (108), and two Half Guards (46) to the Left Base (2) with an M10 x 130mm Bolt (106) and an M10 Nylon Locknut (84). Make sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley. Make sure the Half Guards are oriented as shown. 13 84 108 48 46 46 95 43 72 72 46 106 43 48 46 108 50. Attach the Press Cable (72) to the Small Pulley Plate (50) with an M6 Washer (90) and an M6 50 Nylon Locknut (103). See the inset drawing. Do not completely tighten the Nylon Locknut; it should be tightened so that only two threads of the Cable show past the Nylon Locknut. 21 84 2 103 90 50 72 50 103 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
21
47. Wrap the Press Cable (72) under a Pulley (43).
Attach the Pulley, a Cable Trap (48), an M10
Washer (108), and two Half Guards (46) to the
Left Seat Upright (14) with an M10 x 120mm Bolt
(97) and an M10 Nylon Locknut (84).
Make sure
that the Cable Trap is oriented to hold the
Cable in the groove of the Pulley. Make sure
the Half Guards are oriented as shown.
48.
Note: This step is shown from the opposite
side of the Press Frame (13).
Wrap the Press Cable (72) under a Pulley (43).
Attach the Pulley, a Cable Trap (48), an M10
Washer (108), and two Half Guards (46) to the
Press Frame (13) with an M10 x 45mm Bolt (95)
and an M10 Nylon Locknut (84).
Make sure that
the Cable Trap is oriented to hold the Cable in
the groove of the Pulley. Make sure the Half
Guards are oriented as shown.
49. Wrap the Press Cable (72) under a Pulley (43).
Attach the Pulley, a Cable Trap (48), an M10
Washer (108), and two Half Guards (46) to the
Left Base (2) with an M10 x 130mm Bolt (106)
and an M10 Nylon Locknut (84).
Make sure that
the Cable Trap is oriented to hold the Cable in
the groove of the Pulley. Make sure the Half
Guards are oriented as shown.
108
43
48
46
14
46
72
97
84
47
48
72
43
48
46
95
13
84
108
46
72
43
46
2
50
84
108
49
46
48
106
90
72
50
103
50. Attach the Press Cable (72) to the Small Pulley
Plate (50) with an M6 Washer (90) and an M6
Nylon Locknut (103).
See the inset drawing. Do
not completely tighten the Nylon Locknut; it
should be tightened so that only two threads
of the Cable show past the Nylon Locknut.
72
103
50