Xerox XCARD-SCAN User Guide - Page 75

Properties, Calibrate, Scanners and Cameras, Calibrating from the Windows Control Panel - card scanner 200 windows 7 driver

Get Xerox XCARD-SCAN PDF manuals and user guides View all Xerox XCARD-SCAN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Maintenance 3. Click on the Properties button to open the Device Settings tab for your scanner. 4. Click on the Calibrate button to start the calibration utility. 5. Place the calibration page, with the text and arrow face up, with the arrow pointing into the scanner. The scanner pulls in the calibration page slowly through the scanner. 6. When calibration is complete the scanner will eject the page out of the scanner. Do not forcefully pull the page out, the scanner will release the page when it has fully exited out of the scanner. Calibrating from the Windows Control Panel: If you did not install One Touch during the initial installation of the scanner driver, see page 8, please follow these steps to open the scanner's hardware properties. NOTE: If you are using Windows 2000 or Windows Vista 64-bit, please see "Calibrating or Cleaning the Scanner from TWAIN" on page 64. All other supported versions of Windows can use these instructions or the ones in the TWAIN section. 1. Open the Windows Control Panel. 2. Double-click on Scanners and Cameras. If you do not see Scanners and Cameras, open Printers and Other Hardware then you should see this option. 3. Your Xerox Card Scanner 200 should be listed as one of the attached scanners. Right-click on the scanner and choose Properties to open the Device Settings for your scanner. 4. You can now follow the steps in this section to calibrate the scanner. 70 Xerox Card Scanner 200 User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Maintenance
70
Xerox Card Scanner 200 User’s Guide
3.
Click on the
Properties
button to open the Device Settings tab for your scanner.
4.
Click on the
Calibrate
button to start the calibration utility.
5.
Place the calibration page, with the text and arrow
face up
, with the arrow pointing into the scanner.
The scanner pulls in the calibration page slowly through the scanner.
6.
When calibration is complete the scanner will eject the page out of the scanner. Do not forcefully pull
the page out, the scanner will release the page when it has fully exited out of the scanner.
Calibrating from the Windows Control Panel:
If you did not install One Touch during the initial installation of the scanner driver, see page 8, please
follow these steps to open the scanner’s hardware properties.
NOTE:
If you are using Windows 2000 or Windows Vista 64-bit, please see “Calibrating or Cleaning the
Scanner from TWAIN” on page 64. All other supported versions of Windows can use these instructions or
the ones in the TWAIN section.
1.
Open the Windows Control Panel.
2.
Double-click on
Scanners and Cameras
.
If you do not see Scanners and Cameras, open Printers and Other Hardware then you should see this
option.
3.
Your Xerox Card Scanner 200 should be listed as one of the attached scanners. Right-click on the
scanner and choose Properties to open the Device Settings for your scanner.
4.
You can now follow the steps in this section to calibrate the scanner.