Xerox XTRAVEL-SCAN User Guide - Page 15

Xerox XTRAVEL-SCAN - Travel Scanner 100 Manual

Get Xerox XTRAVEL-SCAN - Travel Scanner 100 PDF manuals and user guides
UPC - 785414114351
View all Xerox XTRAVEL-SCAN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Installation Step 2: Connect the Scanner NOTE: The scanner does not have an external power supply. It draws its power directly from the computer through the USB cable. If you use a USB hub with your computer, the hub must have its own power supply. The scanner does not have an on/off switch. The scanner is ready to scan as soon as its software is finished loading onto your computer. After you plug in the scanner you will be prompted perform a calibration. Please have your calibration page ready. To connect your scanner: 1. Remove any tape from the USB cable. 2. Plug the USB cable into the USB port on the scanner then into a USB port on the computer. Check your computer's manual for USB port locations. If the plug does not attach easily, make sure that you are plugging it in correctly. Do not force the plug into either connection. 3. Your computer recognizes that a scanner has been plugged into the USB port and automatically loads the appropriate software to run the scanner. Do not proceed until you receive a message that your computer has found the new hardware, or updated the driver database. If your computer is running Windows XP or Windows Vista, you will see a message similar to the one below. 10 Xerox Travel Scanner 100 User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Installation
10
Xerox Travel Scanner 100 User’s Guide
Step 2: Connect the Scanner
NOTE:
The scanner does not have an external power supply. It draws its power directly from the computer
through the USB cable. If you use a USB hub with your computer, the hub must have its own power supply.
The scanner does not have an on/off switch. The scanner is ready to scan as soon as its software is finished
loading onto your computer.
After you plug in the scanner you will be prompted perform a calibration. Please have your calibration page
ready.
To connect your scanner:
1.
Remove any tape from the USB cable.
2.
Plug the USB cable into the USB port on the scanner then into a USB port on the computer. Check your
computer’s manual for USB port locations.
If the plug does not attach easily, make sure that you are plugging it in correctly. Do not force the plug
into either connection.
3.
Your computer recognizes that a scanner has been plugged into the USB port and automatically loads
the appropriate software to run the scanner.
Do not proceed until you receive a message that your computer has found the new hardware, or
updated the driver database. If your computer is running Windows XP or Windows Vista, you will see a
message similar to the one below.