Xerox XTRAVEL-SCAN User Guide - Page 74

Xerox XTRAVEL-SCAN - Travel Scanner 100 Manual

Get Xerox XTRAVEL-SCAN - Travel Scanner 100 PDF manuals and user guides
UPC - 785414114351
View all Xerox XTRAVEL-SCAN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Maintenance 3. Click on the Properties button to open the Device Settings for your scanner. 4. Click on the Calibrate button to start the calibration utility. 5. Place the calibration page, with the black bar face down, with the arrows pointing into the scanner. The scanner pulls in the calibration page. The scanner will move the calibration page back and forth during calibration. 6. When calibration is complete the scanner will clear the calibration page out of the scanner. Remove the calibration page when the utility prompts you to. Do not forcefully pull the page out of the scanner, the scanner will release the page when it has fully exited out of the scanner. Calibrating from the Windows Control Panel: If you did not install One Touch during the initial installation of the scanner driver, see page 8, please follow these steps to open the scanner's hardware properties. 1. Open the Windows Control Panel. 2. Double-click on Scanners and Cameras. If you do not see Scanners and Cameras, open Printers and Other Hardware then you should see this option. 3. Your Xerox Travel Scanner 100 should be listed as one of the attached scanners. Right-click on the scanner and choose Properties to open the Device Settings for your scanner. 4. You can now follow the steps in this section to calibrate the scanner. Xerox Travel Scanner 100 User's Guide 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Xerox Travel Scanner 100 User’s Guide
69
Maintenance
3.
Click on the
Properties
button to open the Device Settings for your scanner.
4.
Click on the
Calibrate
button to start the calibration utility.
5.
Place the calibration page, with the black bar
face down
, with the arrows pointing into the scanner.
The scanner pulls in the calibration page. The scanner will move the calibration page back and forth
during calibration.
6.
When calibration is complete the scanner will clear the calibration page out of the scanner. Remove the
calibration page when the utility prompts you to. Do not forcefully pull the page out of the scanner, the
scanner will release the page when it has fully exited out of the scanner.
Calibrating from the Windows Control Panel:
If you did not install One Touch during the initial installation of the scanner driver, see page 8, please
follow these steps to open the scanner’s hardware properties.
1.
Open the Windows Control Panel.
2.
Double-click on
Scanners and Cameras
.
If you do not see Scanners and Cameras, open Printers and Other Hardware then you should see this
option.
3.
Your Xerox Travel Scanner 100 should be listed as one of the attached scanners. Right-click on the
scanner and choose Properties to open the Device Settings for your scanner.
4.
You can now follow the steps in this section to calibrate the scanner.