Yamaha M3000-24 Owner's Manual - Page 35
Control change table, MIDI OUT connector.
View all Yamaha M3000-24 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 35 highlights
responding program change message will be transmitted. If this is set to " " (local), the corresponding program change will be transmitted even when you select a scene for which data has not been saved, thus allowing you to select programs on an external device. (control change transmission/reception oFF/GrP/on This specifies whether or not control change messages will be transmitted and received via MIDI IN/OUT. If this is set to " ," control change messages will not be transmitted or received. If this is set to " ," control changes 1-104 received from an external device will switch the corresponding channel on/off. (If mute groups can be used, control changes 105-112 can also be used to switch mute groups 1-8 on/off.) Also, when the ON/EDIT switches of the M3000 are operated, the corresponding control change will be transmitted. If this is set to " ," only control change numbers (105-112) which correspond to mute groups will be transmitted. (program change reception omni on/off on/oFF This specifies whether or not the MIDI channel specified by the CH (MIDI channel) parameter will be valid. When this setting is " ," program changes will be received on all MIDI channels. When this setting is " ," program changes will be received only on the MIDI channel specified by the CH (MIDI channel) parameter. (echo back on/oFF When this parameter is " ," messages received at the MIDI IN connector will be retransmitted from the MIDI OUT connector. However if a bulk dump request is received, bulk dump data will be output, and the bulk dump request message itself will not be retransmitted (echoed). (bulk out ALL/1-128 This operation transmits all scene memories (ALL) or a specified scene memory (1-128) as MIDI bulk dump data from the MIDI OUT connector. Select " " or " " ~ " " and then press the STORE switch to begin transmission. During transmission, the display will indicate " ." (bulk dump request ALL/1-128 This operation transmits a request for a bulk dump from the MIDI OUT connector. If the respective MIDI IN/OUT connectors of two M3000 units are connected, such a request will cause all scene memories (ALL) or the specified scene memory (1-128) of the other M3000 to overwrite the scene memory (or memories) of this M3000. After selecting " " or " " ~ " ," press the STORE switch to transmit the bulk dump request MIDI message. About the Scene Memory function Control change table The following table shows the M3000 channel/bus to which each control number is assigned. If the CC (control change) item is turned ON in utility mode, a control change message with a value of 127 received from an external device will turn on the corresponding channel/bus, and a control change message with a value of 0 will turn it off. In the same way, operating the ON/EDIT switches of the M3000 will transmit the corresponding control change message from the MIDI OUT connector. Also, if mute groups can be used (refer to page 36), control change numbers 105-112 can be used to switch mute groups 1-8 on/off. Control No. ON/EDIT Switch 0 1 CH INPUT 1 2 CH INPUT 2 3 CH INPUT 3 4 CH INPUT 4 5 CH INPUT 5 6 CH INPUT 6 7 CH INPUT 7 8 CH INPUT 8 9 CH INPUT 9 10 CH INPUT 10 11 CH INPUT 11 12 CH INPUT 12 13 CH INPUT 13 14 CH INPUT 14 15 CH INPUT 15 16 CH INPUT 16 17 CH INPUT 17 18 CH INPUT 18 19 CH INPUT 19 20 CH INPUT 20 21 CH INPUT 21 22 CH INPUT 22 23 CH INPUT 23 24 CH INPUT 24 25 CH INPUT 25 26 CH INPUT 26 27 CH INPUT 27 28 CH INPUT 28 29 CH INPUT 29 Control No. ON/EDIT Switch 30 CH INPUT 30 31 CH INPUT 31 32 CH INPUT 32 33 CH INPUT 33 34 CH INPUT 34 35 CH INPUT 35 36 CH INPUT 36 37 CH INPUT 37 38 CH INPUT 38 39 CH INPUT 39 40 CH INPUT 40 41 42 43 44 45 46 47 48 49 ST INPUT 1 50 ST INPUT 2 51 ST INPUT 3 52 ST INPUT 4 53 54 55 56 57 58 59 35