Yamaha M3000-24 Owner's Manual - Page 7
M1-M8, M9-M12, M13/M14, switches, mix level controls, pan controls
View all Yamaha M3000-24 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
I M1-M8 switches These switch on/off the signal which is sent from the input channel to MIX buses 1-8. Note: If these switches are off, no signal will be sent to the corresponding MIX bus from this input channel, regardless of the switch setting of the variable/fixed select section (page 13). J M1-M8 mix level controls These controls send the signal from the input channel to MIX buses 1-8. When the control is in the "v" position, the level is nominal (0 dB). Use the PRE switch (P) to switch between pre/post fader. Note: For MIX bus pairs for which the variable/fix select section (page 13) switch is set to FIX, the output level which is sent from each input channel to the bus will be fixed, and therefore the mix level control setting will have no effect. K M9-M12 switches These are on/off switches for the signals that are sent from the input channel to MIX buses 9-12. L M9-M12 mix level controls These controls send the signal from the input channel to MIX buses 9-12. When the control is in the "v" position, the level is nominal (0 dB). Use the PRE switch (P) to switch between pre/post fader. Control panel M M13/M14, M15/M16 switches These are on/off switches for the signals that are sent from the input channel to MIX buses 13-16. M13 and 14, and M15 and M16 are stereo pairs, and each pair is turned on/off by one switch. Use the PRE switch (P) to switch between pre/post fader. N M13/M14, M15/M16 mix level controls These controls send the signal from the input channel to MIX buses 13-16. When the control is in the "v" position, the level is nominal (0 dB). M13 and M14, and M15 and M16 are stereo pairs, and the output level of each pair is controlled by one knob. Use the PRE switch (P) to switch between pre/post fader. O M13/M14, M15/M16 pan controls These controls set the panning of the signals that are sent from the input channel to MIX buses 13/14 or MIX buses 15/16. When the control is in the center position, an equal amount of signal will be sent to both buses. P PRE switches These are pre-fader/post-fader switches for the signals that are sent from the input channel to MIX buses 1- 16. Pre/post can be switched independently for each group of MIX buses: 1-4, 5-8, 9-12, and 13-16. When the switch is pressed ( ), the post-EG/pre-fader signal will be sent to the corresponding group of MIX buses. Input 1-24/1-40 +48V PHANTOM MASTER PAD HA 26dB GAIN +48V HPF HPF INSERT I/O 4 Stage EQ PEAK NOM SIGNAL VCA EQ f LO g f LO-MID g Q f HI-MID g Q f HI g 1 2 from VCA Master 7 8 CHECK ON from Ctrl Master CONTROL ON/EDIT Internal Jumper DIRECT OUT MIX MIX (VARIABLE) (FIX) PFL ST 1 3 5 7 9 11 13 15 1 2 3 4 5 6 7 8 L R ON L R 2 4 6 8 10 12 14 16 ST PAN PRE M1 M2 M3 M4 PRE M5 M6 M7 M8 PRE PRE PFL M9 M10 M11 M12 M13/ M14 PAN M15/ PAN M16 7