Yamaha RX-V2200 Owner'w Manual - Page 75

Changing Parameter Settings, Resetting a Parameter to the Factory-set Value

Page 75 highlights

INTRODUCTION PREPARATION BASIC OPERATION Changing Parameter Settings You can enjoy good quality sound with the factory-set parameters. Although you do not have to change the initial settings, you can change some of the parameters to better suit the input source or your listening room. Adjustments should be made with the remote control. y • We recommended that you edit the parameter while using a video monitor. It is easier to see the video monitor than it is to see the front panel display. 3 4 2 5 10KEY DSP 6.1/ES CHP/INDEX HALL 1 HALL 2 1 2 ROCK ENTER- CONCERT TAINMENT 5 6 MOVIE MOVIE THEATER 1 THEATER 2 9 10 0 CHURCH 3 TV SPORTS 7 /DTS SUR. 11 +10 JAZZ CLUB 4 MONO MOVIE 8 SELECT 12 +100 A/B/C/D/E PRESET TV INPUT TV VOL CH TV MUTE MUTE STEREO VOLUME DISC EFFECT ON SCREEN LEVEL SLEEP TEST PARAMETER SET MENU 1 1 Set PARAMETER/SET MENU to PARAMETER. PARAMETER SET MENU 2 Turn on the video monitor and press ON SCREEN repeatedly to select the full display mode. ON SCREEN 3 Select a DSP program you want to adjust. 10KEY DSP HALL 1 HALL 2 1 2 ROCK ENTER- CONCERT TAINMENT 5 6 MOVIE MOVIE THEATER 1 THEATER 2 9 10 0 CHURCH 3 TV SPORTS 7 /DTS SUR. 11 +10 JAZZ CLUB 4 MONO MOVIE 8 SELECT 12 +100 Program No. Program name Cursor P05 ROCK CONCERT ≥ INIT.DLY............15ms ROOM SIZE............1.0 LIVENESS 5 REV.TIME............1.6s REV.DELAY......120ms REV.LEVEL 7% Parameters Parameter valves Example of the parameter setting display SOUND FIELD PROGRAM PARAMETER EDITING 4 Press k / n to select the parameter. 5 Press -/+ to change the parameter value. y • When you set the parameter to a value other than the factoryset value, an asterisk mark (*) appears by the parameter name on the video monitor. 6 Repeat steps 3 to 5 above as necessary to change other program parameters. Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cord is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the parameter value you edited will return to the factory setting. If so, edit the parameter value again. Resetting a Parameter to the Factory-set Value I To reset some of the parameters to the factory-set values Select the parameter you want to reset. Then press and hold -/+ until the value temporarily stops at the factoryset value. The asterisk mark (*) by the parameter name disappears on the video monitor. I To reset all of the parameters to the factory-set values Use "9 PARAM. INI" on the SET MENU to reset all of the parameter values of all DSP programs within the selected group to the factory-set values (see page 63). This operation resets all of the parameter values of all DSP programs within that group to the factory-set values. Notes • The available parameters may be displayed on more than one OSD page for some of the programs. To scroll through pages, press k / n. • You cannot change parameter values when "14 MEMORY GUARD" on the SET MENU is set to ON. If you want to change the parameter values, set "14 MEMORY GUARD" to OFF (see page 65). ADVANCED OPERATION ADDITIONAL INFORMATION APPENDIX English 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88

71
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SOUND FIELD PROGRAM PARAMETER EDITING
4
Press
k
/
n
to select the
parameter.
5
Press
/+ to change the
parameter value.
y
When you set the parameter to a value other than the factory-
set value, an asterisk mark (*) appears by the parameter name
on the video monitor.
6
Repeat steps 3 to 5 above as necessary to
change other program parameters.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the parameter value you edited will
return to the factory setting. If so, edit the parameter
value again.
Resetting a Parameter to the
Factory-set Value
To reset some of the parameters
to the factory-set values
Select the parameter you want to reset. Then press and
hold
/+ until the value temporarily stops at the factory-
set value. The asterisk mark (*) by the parameter name
disappears on the video monitor.
To reset all of the parameters to
the factory-set values
Use
9 PARAM. INI
on the SET MENU to reset all of
the parameter values of all DSP programs within the
selected group to the factory-set values (see page 63).
This operation resets all of the parameter values of all
DSP programs within that group to the factory-set values.
Notes
The available parameters may be displayed on more than one
OSD page for some of the programs. To scroll through pages,
press
k
/
n
.
You cannot change parameter values when
14 MEMORY
GUARD
on the SET MENU is set to ON. If you want to
change the parameter values, set
14 MEMORY GUARD
to
OFF (see page 65).
Changing Parameter Settings
You can enjoy good quality sound with the factory-set
parameters. Although you do not have to change the
initial settings, you can change some of the parameters to
better suit the input source or your listening room.
Adjustments should be made with the remote control.
y
We recommended that you edit the parameter while using a
video monitor. It is easier to see the video monitor than it is to
see the front panel display.
1
Set PARAMETER/SET
MENU to PARAMETER.
2
Turn on the video monitor
and press ON SCREEN
repeatedly to select the
full display mode.
3
Select a DSP program you want to adjust.
PARAMETER
SET MENU
P05
ROCK
CONCERT
ROOM
SIZE…………1.0
LIVENESS…………………5
REV.TIME…………1.6s
REV.DELAY……120ms
REV.LEVEL……………7%
INIT.DLY…………15ms
HALL 1
DSP
10KEY
ROCK
CONCERT
MOVIE
THEATER 1
MOVIE
THEATER 2
TV
SPORTS
MONO
MOVIE
ENTER-
TAINMENT
HALL 2
CHURCH
JAZZ CLUB
SELECT
/DTS
SUR.
1
5
9
6
10
0
10
100
11
12
7
8
2
3
4
+
+
ON SCREEN
Program No.
Example of the parameter setting display
Parameters
Cursor
Program name
HALL 1
6.1/ES
DSP
10KEY
ROCK
CONCERT
MOVIE
THEATER 1
MOVIE
THEATER 2
MUTE
VOLUME
STEREO
TV INPUT
TV VOL
CH
PRESET
DISC
PARAMETER
SET MENU
EFFECT
LEVEL
ON SCREEN
TEST
SLEEP
TV MUTE
TV
SPORTS
MONO
MOVIE
ENTER-
TAINMENT
HALL 2
CHURCH
JAZZ CLUB
SELECT
/DTS
SUR.
CHP/INDEX
A/B/C/D/E
1
5
9
6
10
0
10
100
11
12
7
8
2
3
4
+
+
1
3
4
2
5
Parameter valves