Yamaha YSP 1000 Owner's Manual - Page 106

Automatically setting up the listening environment This unit employs the YAMAHA Parametric Room Acoustic Optimizer (YPAO) technology for automatic sound beam optimization. Notes • Be advised that it is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress. • Make sure that your listening room is as quiet as possible while the AUTO SETUP procedure is in progress. 1 Press STANDBY/ON to turn on the power of this unit. If a subwoofer with adjustable volume and crossover/high cut frequency controls is connected to this unit, set the volume between 11 and 1 o'clock as viewed on a conventional clockface and set the crossover/high cut frequency to the maximum. STANDBY/ON POWER POWER AV TV DVD AUX YSP VCR STB TV INPUT1 INPUT2 MACRO INPUTMODE SLEEP 2 Turn on the power of your TV. 3 Switch to the video input on your TV using the remote control supplied with the TV. For example, if you connect the supplied video pin cable to the video input 2 jack of your TV, switch to video input 2 on your TV. 7 Press / / / to select and configure each parameter and then press ENTER. CH LEVEL CINEMA DSP MENU TEST ENTER RETURN INSTALLING (Installing) Use to select the installed position of the unit in your listening room. • Select Angle to Wall or corner if the unit is installed in the corner. • Select Parallel to Wall if the unit is installed in parallel with the wall. MOUNTING (Mounting) Use to select the mounted position of the unit in your listening room. • Select WALL if the unit is mounted on the wall. • Select SHELF if the unit is mounted on the shelf. REFLECTING (Reflecting) Use to select the reflectivity of your listening room. • Select NORMAL if your listening room has a normal reflectivity. • Select HI ECHO if your listening room has highly reflective surfaces such as concrete walls. 8 Press ENTER to start the AUTO SETUP procedure. ENVIRONMENT CHECK (Environmental noise check), SUB WOOFER CHECK (Subwoofer check) and WILL START in 10 SEC (Will start in 10 sec) are displayed in order as the PREPARATION procedure is in progress. It takes about three minutes for the entire AUTO SETUP procedure to be completed. p p p p p p 4 Press MENU. CH LEVEL CINEMA DSP MENU TEST ENTER RETURN SET MENU . ;MEMORY ;AUTO SETUP ;BASIC SETUP ;MANUAL SETUP [ ]/[ ]:Up/Down [ENTER]:Enter 5 Press / to select AUTO SETUP and then press ENTER. CH LEVEL CINEMA DSP MENU TEST ENTER RETURN ;AUTO SETUP . BEAM+SOUND OPTIMZ BEAM OPTIMZ only SOUND OPTIMZ only [ ]/[ ]:Up/Down [ENTER]:Enter CH LEVEL CINEMA DSP MENU TEST ENTER RETURN PREPARATION . ENVIRONMENT CHECK ;;;[OK] SUB WOOFER CHECK ;;;[NOT IN USE] WILL START in 10 SEC Move aside or behind YSP *****----- y If an error occurs, an error message is displayed. See "Error messages for AUTO SETUP" on page 35 in the Owner's Manual for a complete list of error messages and their proper remedies. Follow the instructions and press RETURN to perform the AUTO SETUP procedure again. 9 Check that the following screen is displayed on your TV. Example of the SHOW RESULT screen SHOW RESULT BEAM MODE: 5BEAM SUBWOOFER: NOT APPLICABLE 6 Press / ENTER. to select BEAM OPT+SOUND OPTIMZ and then press CH LEVEL CINEMA DSP MENU TEST ENTER RETURN PREPARATION . INSTALLING;;Parallel to Wall MOUNTING;;;;SHELF REFLECTING;;NORMAL Set MIC in front of YSP MIN 2m/6.5ft [ ]/[ ]:Up/Down/[p]/[ ]:Sel [ENTER]:Start p [ENTER]:Enter [RETURN]:Cancel 10 Press ENTER to confirm the results. CH LEVEL CINEMA DSP MENU TEST ENTER RETURN AUTO SETTING COMPLETED Enjoying surround sound ■ Enjoying TV in surround sound y Before performing the steps below, set the volume of this unit to -40 dB. 1 Select the TV channel you want to watch using the remote control supplied with your TV. 2 Press TV to select TV as the input source. STANDBY/ON POWER POWER AV TV DVD AUX YSP VCR STB TV INPUT1 INPUT2 MACRO INPUTMODE SLEEP 3 If you hear sound output from your TV speakers, turn down the volume level using the remote control supplied with your TV until you cannot hear any sound. 4 Press VOLUME +/- to adjust the volume level. VOLUME CH TV VOL ■ Enjoying DVDs in surround sound y Before performing the steps below, set the volume of this unit to -40 dB. 1 Switch to the video input on your TV using the remote control supplied with your TV so that the DVD menu screen is displayed. 2 Press DVD to select DVD as the input source and then start playback on the DVD player. STANDBY/ON POWER POWER AV TV DVD AUX YSP VCR STB TV INPUT1 INPUT2 MACRO INPUTMODE SLEEP 3 If you hear sound output from your TV speakers, turn down the volume level using the remote control supplied with your TV until you cannot hear any sound. 4 Press VOLUME +/- to adjust the volume level. VOLUME CH TV VOL 5 Press YSP to switch to the operation mode of this unit. AUX INPUT1 INPUT2 MACRO YSP INPUTMODE SLEEP 5BEAM 1 ST+3BEAM 2 3BEAM 3 STEREO TARGET 4 5 6 6 Press one of the beam mode buttons to select the desired beam mode. For further details about the beam modes, see page 42 in the supplied Owner's Manual. 5BEAM 1 STEREO 4 MUSIC 7 SPORTS 0 ST+3BEAM 2 3BEAM 3 TARGET 5 6 MOVIE 8 VOL MODE 9 OFF +10 SURROUND y The target mode outputs sound beams in a single channel and is ideal if you do not want the sound beams to be reflected on the walls in your listening room or if you do not disturb others asleep while enjoying music or movies at night. In addition, you can adjust the horizontal angle of the sound beams so that you can hear dialogues clearly even from a distant location such as the kitchen area in your listening room. For further details about the target mode, see page 45 in the supplied Owner's Manual. 7 Press VOL MODE repeatedly to select the desired volume mode. The volume modes are designed to improve listenability at lower volumes and limit the volume level of the TV so that it will not vary suddenly to a great extent. For further details about the volume modes, see page 56 in the supplied Owner's Manual. STEREO 4 MUSIC 7 SPORTS 0 TARGET 5 MOVIE 8 OFF +10 6 VOL MODE 9 SURROUND 5 Press YSP to switch to the operation mode of this unit. AUX INPUT1 INPUT2 MACRO YSP INPUTMODE SLEEP 5BEAM 1 ST+3BEAM 2 3BEAM 3 STEREO TARGET 4 5 6 6 Press one of the beam mode buttons to select the desired beam mode. For further details about the beam modes, see page 42 in the supplied Owner's Manual. 5BEAM 1 STEREO 4 MUSIC 7 SPORTS 0 ST+3BEAM 2 3BEAM 3 TARGET 5 6 MOVIE 8 VOL MODE 9 OFF +10 SURROUND