Yamaha YSP 1000 Owner's Manual - Page 15

PREPARATION, INSTALLATION, Before installing this unit - bracket

Get Yamaha YSP 1000 - Digital Sound Projector Five CH Speaker PDF manuals and user guides
UPC - 027108924274
View all Yamaha YSP 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

PREPARATION INSTALLATION INSTALLATION This section describes a suitable installation location to install the unit using a metal wall bracket, a rack or a stand. Before installing this unit Installing this unit This unit creates surround sound by reflecting projected sound beams off the walls of your listening room. The surround sound effects produced by this unit may not be sufficient when the unit is installed in the following locations. • Rooms with surfaces inadequate for reflecting sound beams • Rooms with acoustically absorbent surfaces • Rooms with measurements outside the following range W (3 to 7 m) x H (2 to 3.5 m) x D (3 to 7 m) • Rooms with less than 2 m from the listening position to the speaker positions • Rooms where objects such as furniture are likely to obstruct the path of sound beams • Rooms where the listening position is close to the walls • Rooms where the listening position is not in front of this unit Make sure you leave an adequate amount of ventilation space so that heat can escape. Make at least 5 cm of space above or below this unit. Side view Install this unit where there are no obstacles such as furniture obstructing the path of sound beams. Otherwise, the desired surround sound effects may not be achieved. You may install this unit in parallel with the wall or in the corner. ■ Parallel installation Install this unit in the exact center of the wall when it is measured from the left and right corners. An object, such as furniture Front 5 cm or more Rear Side ■ Corner installation Install this unit in the corner at a 40º to 50º angle from the adjacent walls. 40° to 50° Notes • This unit weighs 13.0 kg. Be sure to install this unit where it will not fall subject to vibrations, such as from an earthquake, and where it is out of the reach of children. • When using a cathode-ray tube (CRT) TV, do not install this unit directly above your TV. • This unit is shielded against magnetic rays. However, if the picture on your TV screen becomes blurred or distorted, we recommend moving the speakers away from your TV. An object, such as furniture y The availability of the beam mode depends on the installation location of this unit (see page 42). All five beam modes are available for the parallel installation whereas the 3 beam and 5 beam modes are not available for the corner installation. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
INSTALLATION
11
PREPARATION
This section describes a suitable installation location to install the unit using a metal wall bracket, a rack or a stand.
This unit creates surround sound by reflecting projected
sound beams off the walls of your listening room. The
surround sound effects produced by this unit may not be
sufficient when the unit is installed in the following
locations.
•
Rooms with surfaces inadequate for reflecting sound
beams
•
Rooms with acoustically absorbent surfaces
•
Rooms with measurements outside the following range
W (3 to 7 m) x H (2 to 3.5 m) x D (3 to 7 m)
•
Rooms with less than 2 m from the listening position to
the speaker positions
•
Rooms where objects such as furniture are likely to
obstruct the path of sound beams
•
Rooms where the listening position is close to the walls
•
Rooms where the listening position is not in front of
this unit
Make sure you leave an adequate amount of ventilation
space so that heat can escape. Make at least 5 cm of space
above or below this unit.
•
This unit weighs 13.0 kg. Be sure to install this unit where it
will not fall subject to vibrations, such as from an earthquake,
and where it is out of the reach of children.
•
When using a cathode-ray tube (CRT) TV, do not install this
unit directly above your TV.
•
This unit is shielded against magnetic rays. However, if the
picture on your TV screen becomes blurred or distorted, we
recommend moving the speakers away from your TV.
Install this unit where there are no obstacles such as
furniture obstructing the path of sound beams. Otherwise,
the desired surround sound effects may not be achieved.
You may install this unit in parallel with the wall or in the
corner.
■
Parallel installation
Install this unit in the exact center of the wall when it is
measured from the left and right corners.
■
Corner installation
Install this unit in the corner at a 40º to 50º angle from the
adjacent walls.
y
The availability of the beam mode depends on the installation
location of this unit (see page 42). All five beam modes are
available for the parallel installation whereas the 3 beam and 5
beam modes are not available for the corner installation.
INSTALLATION
Before installing this unit
Notes
5 cm or more
Rear
Front
Side view
Side
Installing this unit
An object, such as furniture
40° to 50°
An object, such as furniture