3Com 3CRWE875075ATAA User Guide - Page 51

Troubleshooting

Get 3Com 3CRWE875075ATAA - Wireless LAN Access Point 8750 PDF manuals and user guides
UPC - 662705487465
View all 3Com 3CRWE875075ATAA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

3 TROUBLESHOOTING If you have difficulty with the 3Com Wireless LAN access point, first check the following items in the configuration: o Radio Settings page: Ensure that the SSID is the same on clients and the access point. o Security page: Ensure that Encryption is the same on clients and the access point. o Authentication page: Ensure that the Local MAC Authentication System Default is set to Allow. Ensure that 802.1x Authentication Settings are correct. o TCP/IP Settings page: If the DHCP Client is set to Disabled, then ensure that the access point IP Address is within the same subnet as the wired LAN. If necessary, reset the access point to the factory defaults. Try the solutions in the following table. If you need further assistance, contact 3Com Technical Support through the following Web page: http://www.3com.com/products/en_US/supportedindex.jsp Symptom Solutions Access point does not power up. Make sure the Ethernet cable is plugged into the port labeled To Access Point on the power brick. Check for a faulty access point power supply. Check for a failed AC power supply Access point powers up, but has no connection to the wired network. Make sure that the Ethernet cable is plugged into the port labeled To Hub/Switch on the power brick. Verify the network wiring and topology for proper configuration. Check that the cables used are the proper type. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
51
3
T
ROUBLESHOOTING
If you have difficulty with the 3Com Wireless LAN access point, first check the
following items in the configuration:
o
Radio Settings page: Ensure that the SSID is the same on clients and the
access point.
o
Security page: Ensure that Encryption is the same on clients and the access point.
o
Authentication page: Ensure that the Local MAC Authentication System Default is
set to Allow. Ensure that 802.1x Authentication Settings are correct.
o
TCP/IP Settings page: If the DHCP Client is set to Disabled, then ensure that the
access point IP Address is within the same subnet as the wired LAN.
If necessary, reset the access point to the factory defaults.
Try the solutions in the following table. If you need further assistance, contact 3Com
Technical Support through the following Web page:
Symptom
Solutions
Access point does not
power up.
Make sure the Ethernet cable is plugged into the port labeled
To Access Point
on the power brick.
Check for a faulty access point power supply.
Check for a failed AC power supply
Access point powers up, but
has no connection to the wired
network.
Make sure that the Ethernet cable is plugged into the port
labeled To Hub/Switch on the power brick.
Verify the network wiring and topology for proper
configuration. Check that the cables used are the proper type.