3Ware 9650SE-2LPB-10 CLI Guide - Page 89

/cx/bbu show attribute [attribute ...], /cx/bbu show status, Testing., Charging., Fault., Error.

Get 3Ware 9650SE-2LPB-10 - Sataii Raid Hardware 10Pk PDF manuals and user guides
UPC - 693494601022
View all 3Ware 9650SE-2LPB-10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

BBU Object Commands /cx/bbu show attribute [attribute ...] This command shows the current setting of the given attribute(s) on the BBU board. One or many attributes can be specified. Specifying an invalid attribute will terminate the loop. Possible attributes are: batinst, bootloader, cap, fw, lasttest, pcb, ready, status, serial, temp, volt. /cx/bbu show status This command shows the status of the BBU. Possible values are: Testing. A battery test is currently in progress. This test may take up to 24 hours to complete. During the test, the BBU is not capable of backup operation and the write cache of the RAID controller is also disabled. If the test is completed with no error and the BBU status changes to WeakBat or OK, the write cache will be re-enabled. If a Fault, Failed or Error occurs during the test, the write cache remains in the disabled state until the problem is fixed. Charging. The BBU is currently charging the battery. Charging is started automatically by the BBU whenever necessary. During charging, the BBU is not capable of backup operation and the write cache is disabled. Once the test is completed with no error and the BBU status changes to OK, the write cache will be re-enabled. If a FAULT or ERROR occurs during the test, the write cache remains in the disabled state until the problem is fixed. Fault. A battery fault is detected. The BBU is not capable of backup operation and the write cache is disabled. Replace the battery and/or the BBU board as soon as possible so that the write cache will be enabled again. Error. A BBU error is detected. The BBU is not capable of backup operation and the write cache is disabled. Replace the battery and/or the Battery Backup Unit as soon as possible so that the write cache will be enabled again. Failed. The battery failed a test. In this state, the BBU is not capable of backup operation and the write cache is disabled. We recommend you replace the battery and/or the Battery Backup Unit as soon as possible so that the write cache will be enabled again. WeakBat. The BBU is functioning normally and is online and capable of backing up the write cache. However, the battery is weak and should be replaced. OK. The BBU is ready, online and capable of backing up the write cache. - (dash) A battery is not present or a Battery Backup Unit is not installed www.3ware.com 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
BBU Object Commands
www.3ware.com
83
/c
x
/bbu show
attribute
[
attribute
...]
This command shows the current setting of the given attribute(s) on the BBU
board. One or many attributes can be specified. Specifying an invalid attribute
will terminate the loop. Possible attributes are:
batinst, bootloader, cap, fw,
lasttest, pcb, ready, status, serial, temp, volt.
/c
x
/bbu show
status
This command shows the status of the BBU. Possible values are:
Testing.
A battery test is currently in progress. This test may take up to 24
hours to complete. During the test, the BBU is
not
capable of backup
operation and the write cache of the RAID controller is also disabled. If the
test is completed with no error and the BBU status changes to WeakBat or
OK, the write cache will be re-enabled. If a Fault, Failed or Error occurs
during the test, the write cache remains in the disabled state until the problem
is fixed.
Charging.
The BBU is currently charging the battery. Charging is started
automatically by the BBU whenever necessary. During charging, the BBU is
not capable of backup operation and the write cache is disabled. Once the test
is completed with no error and the BBU status changes to OK, the write cache
will be re-enabled. If a FAULT or ERROR occurs during the test, the write
cache remains in the disabled state until the problem is fixed.
Fault.
A battery fault is detected. The BBU is not capable of backup operation
and the write cache is disabled. Replace the battery and/or the BBU board as
soon as possible so that the write cache will be enabled again.
Error.
A BBU error is detected. The BBU is not capable of backup operation
and the write cache is disabled. Replace the battery and/or the Battery Backup
Unit as soon as possible so that the write cache will be enabled again.
Failed.
The battery failed a test. In this state, the BBU is not capable of
backup operation and the write cache is disabled. We recommend you
replace
the battery and/or the Battery Backup Unit as soon as possible so that the
write cache will be enabled again.
WeakBat.
The BBU is functioning normally and is online and capable of
backing up the write cache. However, the battery is weak and should be
replaced.
OK.
The BBU is ready, online and capable of backing up the write cache.
-
(dash) A battery is not present or a Battery Backup Unit is not installed