Alpine CDE-W265BT Owner's Manual (english) - Page 18
Setting the Source Volume Level, Adjusting the Crossover Settings, X-OVER, Turning Subwoofer ON/OFF
View all Alpine CDE-W265BT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 18 highlights
Adjusting the Frequency (CENTER FRQ) Adjustable frequency bands: 20 Hz to 20 kHz Band1 Band2 Band3 Band4 Band5 Band6 Band7 Band8 Band9 20 Hz ~ 100 Hz (63 Hz) 63 Hz ~ 315 Hz (125 Hz) 125 Hz ~ 500 Hz (250 Hz) 250 Hz ~ 1 kHz (500 Hz) 500 Hz ~ 2 kHz (1 kHz) 1 kHz ~ 4 kHz (2 kHz) 2 kHz ~ 7.2 kHz (4 kHz) 5.8 kHz ~ 12 kHz (8 kHz) 9 kHz ~ 20 kHz (16 kHz) Setting the Bandwidth (WIDTH (Q)) Setting contents: 3.0 (Initial setting) / 4.0 / 5.0 Adjusting the Level Setting contents: −7 to +7 (Initial setting: ±0) Notes • BAND2 and BAND8 are the same as the Bass and Treble controls. Their Level adjustment can also be controlled by pressing YSETUP and selecting Bass Level or Treble Level. Refer to "Adjusting Subwoofer Level/Bass Level/Treble Level/Balance (Between Left and Right)/Fader (Between Front and Rear)/Defeat" on page 16. • Settings exceeding the frequency of adjacent bands are not available. • While adjusting the 9BAND P-EQ, you should consider the frequency response of the connected speakers. • The 9-Band, Parametric EQ is used to customize the EQ PRESETS settings. Setting the Source Volume Level The output level of each source is individually adjustable. For example, if the TUNER level sounds lower than CD, its output can be adjusted without affecting the other sources. Setting item: SOURCE VOL Further setting items: TUNER / SIRIUS XM / DISC / USB / IPOD / BT AUDIO / PANDORA / AUX Setting contents: −14 dB ~ +14 dB (Initial setting: ±0) Adjusting the Crossover Settings (X-OVER) Before performing the following procedures, refer to "About the Crossover" on page 22. Setting item: X-OVER 1 Turn the Rotary encoder to select the channel, and then press ENTER. 2WAY System FRONT (HPF) REAR (HPF) SUBW LPF FRONT (HPF) 3WAY System LOW (LPF) MID LOW (HPF) MID HIGH (LPF) HIGH (HPF) LOW 2 Turn the Rotary encoder to select the desired item, and then press ENTER. 18-EN Selecting the Cut-Off Frequency (FREQUENCY) 2WAY System Setting contents: 20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) / 100 / 125 / 160 / 200 (Hz) 3WAY System Setting contents: LOW/MID LOW: 20 / 25 / 31.5 / 40 / 50 / 63 / 80 / 100 / 125 / 160 / 200 / 250 / 315 / 400 / 500 (Initial setting) / 630 / 800 (Hz) MID HIGH: 20 / 25 / 31.5 / 40 / 50 / 63 / 80 / 100 / 125 / 160 / 200 / 250 / 315 / 400 / 500 / 630 / 800 / 1 k / 1.2 k / 1.6 k / 2 k / 2.5 k / 3.2 k / 4 k / 5 k (Initial setting) / 6.3 k / 8 k / 10 k / 12.5 k / 16 k / 20 k (Hz) HIGH: 1 k / 1.2 k / 1.6 k / 2 k /2.5 k / 3.2 k / 4 k / 5 k (Initial setting) / 6.3 k / 8 k / 10 k / 12.5 k / 16 k / 20 k (Hz) Note • The frequency of MID LOW should not be more than the frequency of MID HIGH. Adjusting the Slope (SLOPE) 2WAY System Setting contents: FLAT / 6 / 12 / 18 / 24 (dB/oct.) 3WAY System Setting contents: FLAT / 6 / 12 (dB/oct.) Note • The Initial setting for 2WAY is FLAT. 3WAY is 12. Adjusting the Level (LEVEL) 2WAY System/3WAY System Setting contents: −12 to 0 (dB) (Initial setting: 0) Note • The level setting results for MID LOW and MID HIGH in 3WAY system are linkage. 3 Repeat steps 1 to 2 to make adjustment to the other channels. Turning Subwoofer ON/OFF When the subwoofer is on, you can adjust the subwoofer output level (refer to "Adjusting Subwoofer Level/Bass Level/Treble Level/Balance (Between Left and Right)/Fader (Between Front and Rear)/Defeat" on page 16). Setting item: SUBWOOFER Setting contents: OFF / ON (Initial setting) OFF: No subwoofer signal is output from the Subwoofer RCA Connectors (refer to "Connections" on page 58). ON: The subwoofer signal is output from the Subwoofer RCA Connectors (refer to "Connections" on page 58).