Asus TRL-DLS TRL-DLS User Manual - Page 18

Memory Installation

Get Asus TRL-DLS PDF manuals and user guides View all Asus TRL-DLS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

60 Pins 20 Pins 3. HARDWARE SETUP 3.5.2 Memory Installation WARNING! Make sure that you unplug the power supply when adding or removing memory modules or other system components. Failure to do so may cause severe damage to both the motherboard and expansion cards (see 3.3 Hardware Setup Procedure for more information). Insert a DIMM into the DIMM socket as shown. Because the number of pins are different on either side of the breaks, the module only fits in one direction. SDRAM DIMMs have different pin contacts on each side. ® TRL-DLS TRL-DLS 168-Pin DIMM Sockets IMPORTANT: Always install DIMMs in pairs. See previous section for the memory configurations. Use only 3.3Volt "registered" SDRAM DIMMs. To determine the DIMM type, check the notches on the DIMMs (see the figure below). 88 Pins 3. H/W SETUP System Memory The notches on the DIMM shifts between left, center, or right to identify the type and also to prevent the wrong type from being inserted into the DIMM slot on the motherboard. You must tell your retailer the correct DIMM type before purchasing. This motherboard supports four clock signals per DIMM. 18 ASUS TRL-DLS User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
18
ASUS TRL-DLS User’s Manual
3. HARDWARE SETUP
Insert a DIMM into the DIMM socket as shown. Because the number of pins are
different on either side of the breaks, the module only fits in one direction. SDRAM
DIMMs have different pin contacts on each side.
The notches on the DIMM shifts between left, center, or right to identify the type
and also to prevent the wrong type from being inserted into the DIMM slot on the
motherboard. You must tell your retailer the correct DIMM type before purchasing.
This motherboard supports four clock signals per DIMM.
Use only 3.3Volt “registered” SDRAM DIMMs. To determine the DIMM type, check
the notches on the DIMMs (see the figure below).
WARNING!
Make sure that you unplug the power supply when adding or
removing memory modules or other system components. Failure to do so may
cause severe damage to both the motherboard and expansion cards (see
3.3
Hardware Setup Procedure
for more information).
System Memory
3. H/W SETUP
3.5.2
Memory Installation
IMPORTANT:
Always install DIMMs in pairs. See previous section for the
memory configurations.
TRL-DLS
TRL-DLS 168-Pin DIMM Sockets
20 Pins
60 Pins
88 Pins