BenQ BenQ MW860USTi Ultra Short-Throw 3D Projector MW860USTi User Manual - Page 30

Operation, Starting up the projector

Get BenQ BenQ MW860USTi Ultra Short-Throw 3D Projector PDF manuals and user guides View all BenQ BenQ MW860USTi Ultra Short-Throw 3D Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Operation Starting up the projector 1. Plug the power cord into the projector and into a power outlet. Check that the POWER indicator light on the projector lights orange after power has been applied. • Please use the original accessories (e.g. power cable) only with the device to avoid possible dangers such as electric shock and fire. • If Direct power on function is activated in the SYSTEM SETUP: Basic > Operation Settings menu, the projector will turn on automatically after the power cord has been connected and power has been applied. See "Direct Power On" on page 77 for details. 2. Make sure the lens cover is open. If it is closed, it could become deformed due to the heat produced by the projection lamp. MP780 ST+ MW860USTi 3. Press II Power on the projector or ON on the remote control to start the projector. The POWER indicator light flashes and stays green when the projector is on. The start up procedure takes about 10-20 seconds. In the later stage of start up, a startup logo is projected. (If necessary) Use the focus ring/focus slide lever to adjust the image clearness. If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp. 30 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Operation
30
Operation
Starting up the projector
1.
Plug the power cord into the projector and into
a power outlet. Check that the
POWER
indicator light
on the projector lights orange
after power has been applied.
•
Please use the original accessories (e.g. power cable)
only with the device to avoid possible dangers such as
electric shock and fire.
•
If Direct power on function is activated in the
SYSTEM SETUP: Basic > Operation Settings menu, the projector will turn on automatically
after the power cord has been connected and power has been applied. See
"Direct Power
On" on page 77
for details.
2.
Make sure the lens cover is open. If it is
closed, it could become deformed due
to the heat produced by the projection
lamp.
3.
Press
Power
on the projector or
ON
on the remote control to start the
projector. The
POWER indicator light
flashes and stays green when the projector is
on.
The start up procedure takes about 10-20
seconds. In the later stage of start up, a
startup logo is projected.
(If necessary) Use the focus ring/focus slide
lever to adjust the image clearness.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90
seconds before energizing the lamp.
MP780 ST+
MW860USTi
I
I