BenQ BenQ MW860USTi Ultra Short-Throw 3D Projector MW860USTi User Manual - Page 50

Controlling the projector through a LAN environment, Configuring the Wired LAN Settings

Get BenQ BenQ MW860USTi Ultra Short-Throw 3D Projector PDF manuals and user guides View all BenQ BenQ MW860USTi Ultra Short-Throw 3D Projector manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Controlling the projector through a LAN environment Network Settings allow you to manage the projector from a computer using a web browser when the computer and the projector are properly connected to the same local area network. Configuring the Wired LAN Settings If you are in a DHCP environment: 1. Take a RJ45 cable and connect one end to the LAN input jack of the projector and the other end to the RJ45 port. 2. Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted. 3. Press to highlight Network Settings and press MODE/ENTER. The Network Settings page displays. 4. Press to highlight Wired LAN and press MODE/ENTER. 5. Press to highlight DHCP and press / to select On. 6. Press to highlight Apply and press MODE/ENTER. 7. Re-enter the Wired LAN page. The IP Address, Subnet Mask, Default Gateway, and DNS settings will be displayed. Note down the IP address. If the IP Address still does not display, contact your ITS administrator. If you are in a non-DHCP environment: 1. Repeat steps 1-4 above. 2. Press to highlight DHCP and press / to select Off. 3. Contact your ITS administrator for information on the IP Address, Subnet Mask, Default Gateway, and DNS settings. 4. Press to select the item you want to modify and enter the value. 5. Press to highlight Apply and press MODE/ENTER. Configuring the Wireless LAN Settings 1. Connect the BenQ wireless dongle (optional) to the USB TYPE-A input jack of the projector. 2. Highlight Wireless LAN in SYSTEM SETUP: Advanced > Network Settings menu and press MODE/ENTER. 3. For AP mode connection, you need to note SSID information, then search the projector with the same SSID in Q Presenter to start projection. For 50 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Operation
50
Controlling the projector through a LAN
environment
Network Settings allow you to manage the projector from a computer using a web
browser when the computer and the projector are properly connected to the same local
area network.
Configuring the Wired LAN Settings
If you are in a DHCP environment:
1.
Take a RJ45 cable and connect one end to the LAN input jack of the projector and
the other end to the RJ45 port.
2.
Press
MENU/EXIT
and then press
/
until the
SYSTEM SETUP:
Advanced
menu is highlighted.
3.
Press
to highlight
Network Settings
and press
MODE/ENTER
. The
Network Settings
page displays.
4.
Press
to highlight
Wired LAN
and press
MODE/ENTER
.
5.
Press
to highlight DHCP and press
/
to select On.
6.
Press
to highlight Apply and press
MODE/ENTER
.
7.
Re-enter the
Wired LAN
page. The IP Address, Subnet Mask, Default Gateway, and
DNS settings will be displayed. Note down the IP address.
If the IP Address still does not display, contact your ITS administrator.
If you are in a non-DHCP environment:
1.
Repeat steps 1-4 above.
2.
Press
to highlight DHCP and press
/
to select Off.
3.
Contact your ITS administrator for information on the IP Address, Subnet Mask,
Default Gateway, and DNS settings.
4.
Press
to select the item you want to modify and enter the value.
5.
Press
to highlight Apply and press
MODE/ENTER
.
Configuring the Wireless LAN Settings
1.
Connect the BenQ wireless dongle (optional) to the USB TYPE-A input jack of the
projector.
2.
Highlight
Wireless LAN
in
SYSTEM SETUP: Advanced
>
Network Settings
menu and press
MODE/ENTER
.
3.
For
AP
mode connection, you need to note SSID information, then search the
projector with the same SSID in Q Presenter to start projection. For