Bosch DHR-1600A-150A Installation Manual - Page 25

Camera connections

Get Bosch DHR-1600A-150A PDF manuals and user guides View all Bosch DHR-1600A-150A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Divar XF Placing a hard disk Hardware setup | en 25 4.4 Figure 4.4 Placing a hard disk 1. Locate the first empty hard disk bay. It is recommended that you install the disks in order from one to four, as labeled. (Note that disks 3 and 4 are mounted in a double bay.) 2. Unscrew the two torx T10 screws securing the selected bay. Slide the bay from the unit by pulling it forward. 3. To replace an installed hard disk, remove the four installation screws, two per side, from the sides of the bay. Remove the hard disk. Mount the new hard disk into the bay with four screws, two per side (refer to the hard disk documentation). 4. Align and slide the bay back fully into its slot in the unit. 5. Secure the bay using the two torx T10 screws removed earlier (step 2). 6. Repeat steps 1-5 for any additional hard disks. Remounting the front panel 1. When disk installation is complete, reconnect the flat cable to the front panel, if necessary. 2. Align and slide the front panel to the left until it is in place. 3. Refasten the two captive cross head screws to the front panel. Camera connections Connect cameras to the Video in connectors on the back of the unit using 75 ohm video coaxial cables with BNC connectors. Optionally, this signal can be looped through to other equipment via the corresponding Video out connector. The camera input connectors are auto- Bosch Security Systems Installation manual F.01U.135.429 | 2.5 | 2009.08

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Divar XF
Hardware setup | en
25
Bosch Security Systems
Installation manual
F.01U.135.429 | 2.5 | 2009.08
Placing a hard disk
Figure 4.4
Placing a hard disk
1.
Locate the first empty hard disk bay. It is recommended that you install the disks in order
from one to four, as labeled. (Note that disks 3 and 4 are mounted in a double bay.)
2.
Unscrew the two torx T10 screws securing the selected bay. Slide the bay from the unit
by pulling it forward.
3.
To replace an installed hard disk, remove the four installation screws, two per side, from
the sides of the bay. Remove the hard disk.
Mount the new hard disk into the bay with four screws, two per side (refer to the hard
disk documentation).
4.
Align and slide the bay back fully into its slot in the unit.
5.
Secure the bay using the two torx T10 screws removed earlier (step 2).
6.
Repeat steps 1-5 for any additional hard disks.
Remounting the front panel
1.
When disk installation is complete, reconnect the flat cable to the front panel, if
necessary.
2.
Align and slide the front panel to the left until it is in place.
3.
Refasten the two captive cross head screws to the front panel.
4.4
Camera connections
Connect cameras to the
Video in
connectors on the back of the unit using 75 ohm video
coaxial cables with BNC connectors. Optionally, this signal can be looped through to other
equipment via the corresponding
Video out
connector. The camera input connectors are auto-